Product Categories

About Us

cable, vdsl, patch

 

Cable Tray Distributor - M E 2 Wire Cable Tray System Accessories - Cabletray Supplier - Cable Trays - Cable Tray Systems -
Basket Tray - Raceway Systems

American Tech Supply Is Your One Source For All Your Cable Tray-Cable Trays - Cable Tray Systems - Basket Tray - Raceway Systems

PRO-10 Wire Cable Tray System M.E.2 Wire Cable Tray System

M.E.2 Wire Cable Tray System

Accessories

Splice Washer Kit #05-2-600726

The cable tray straight and junction sections are easily joined together using installer-friendly splice washers kits. The kit contains one 1/4”-20 bolt washer, one splice washer, and one flanged hex nut. Material is zinc plated steel.

Splice Washer Usage Per Tray Connection
6”
8”
12”
18”
24”
3 kits
4 kits
5 kits

Tray Connection Loop Kit #05-2-500981(only for tray widths 12” or less)

Splice connection loops are used to connect adjacent tray sections as a time saving alternative to use of splice washers. The kit contains one connection loop, one square washer, and one 5/16” carriage bolt and hex nut. Connection loop material is galvanized steel. Square washer material is zinc plated steel.

M.E.2 Cable Tray Mounting and Support Accessories

Center and trapeze supports are available when hanging the trays by using either 3/8” or 1/4” diameter threaded rods*, which are supplied by the installer. The cable trays can be also mounted along the sides of walls using wall mount brackets. A floor support is used when installing M.E.2 cable trays under raised flooring.

Center Support Kit #CM50XX-3: (2) 1/4” hex nut (1) 6” protective tubing (1) center support with hold down bracket

Center Support Kit #CM51XX-3: (2) 3/8” hex nut (1) 6” protective tubing (1) center support with hold down bracket

Trapeze Support Kit #CM52XX-3: (4) 1/4” flat washers (4) 1/4” hex nuts

Trapeze Support Kit #CM53XX-3: (4) 3/8” flat washers (4) 3/8” hex nuts

Center Support Kit
#CM50XX-3
#CM51XX-3
Trapeze Support Kit
#CM52XX-3
#CM53XX-3
Wall Mount Support
#CM57XX-3
Floor Support
#CM56XX-3
Cable Drop Out
Waterfall

#CM59-3
XX= Width of tray section ordered; 6”, 8”, 12”, 18” or 24”. Material for supports is steel wire, powder coated chrome color.
*Threaded rod is not included in support kits and must be furnished by the installer.
Coupling Nuts
#CM60 1/4"-20
#CM61 3/8"-16
Flat Washers
#CM62 1/4"
#CM63 3/8"
Finned Nuts
#CM65 1/4"-20
#CM66 3/8"-16
#CM67 5/16"-18
Carriage Bolts
#CM68 5/16"-18 x 3/4"
#CM72 5/16"-18 x 1 1/4"
Split Bolt for Grounding
#05-2-600727
   
Ratchet
#CM99
Cable Tray Cutter
#05-2-600728
Protective Tubing
#CM69 6" for
1/4" & 3/8" rod
   

Accessories

Tray Divider #05-2-500983 for a 2” deep tray or #05-2-500984 for a 4” deep tray
The dividers are made from galvanized zinc plated steel and are 5’ long.
(requires two splice washer assemblies #05-2-500985 used to secure to each tray section)

Cable Tray Divider
Splice Washer Assembly #05-2-500985
Used for securing tray dividers to tray section. Included (1) 1/4”-20 bolt and nut (1) splice washer
Hold Down Bracket #05-2-500982
Used to secure tray sections to hanging or floor supports. Material is steel wire powder coated chrome color 4” long.

Hold Down Bracket
Universal Beam Clamp for hanging of threaded rods
The universal beam clamps are made from zinc plated steel and fit 5/8” max beam flange.
05-CM100 fits 1/4”-20 threaded rod in bottom or side tapped hole
05-CM101 fits 3/8”-16 threaded rod in bottom or side tapped hole

Universal Beam Clamp

Cable Tray Support Brackets

C Support Bracket

 

L Support Bracket

Model
Length
Model
Length
05-CM24-04201
6"
05-CM18-04201
6"
05-CM24-04202
8"
05-CM18-04201
8"
05-CM24-04205
12"
05-CM18-04201
12"
05-CM24-04208
18"
05-CM18-04201
18"
05-CM24-04210
24"
05-CM18-04201
24"


C Support Bracket

L Support Bracket

Cable Tray Raised Floor Pedestal Supports

05-CM74-3 Angle Pedestal Support Kit - includes (2) Angle Supports and (2) "U" clamps
Clamps fit up to a 1 ½” dis. Pedestal


05-CM75-3 Raised Floor Pedestal Bridge Support Kit - includes (1) Bridge Support and (2) "U" clamps
Spans 24 inch center to center floor pedestals up to 1 1/2" dia.

Solid Bottom Plate

Model
Dimensions
Width x Length
05-2-06BP
6” x 59”
05-2-08BP
8” x 59”
05-2-12BP
12” x 59”
05-2-18BP
18” x 59”
05-2-24BP
24” x 59”
• Galvanized steel or powder coated to provide a smooth protective surface for cable pulling
• Can be supplied pre-assembled to cable trays or installed in the field with #05-2-500985 Splice Washer Assys. 4/plate
• Available in easy to handle 59” lengths
• Fits cable trays 6, 8, 12, 18 and 24 inches wide
 

Cable Tray Cover

Model
Dimensions
Width x Length
05-CM21-04
4" x 59”
05-CM21-06
6" x 59”
05-CM21-08
8" x 59”
05-CM21-12
12" x 59”
05-CM21-18
18" x 59”
05-CM21-24
24" x 59”

Cable Tray Cover
Cable Tray Cover


The M.E.2 cable management system is manufactured with rigid .187 diameter zinc plated steel wire, welded in a 2 inch x 4 inch grid. M.E.2 cable trays can be configured at the installation site. Seven or 10 foot straight tray sections are easy to handle. Two or 4 inch deep trays available in 6, 8, 12, 18 and 24 inch widths, offer a wide variety of wire channel routing and protection options. The 2 x 4 inch grid design facilitates simple cable break outs while supporting the cable. The open grid design prevents dirt and dust build-up experienced in closed cable trays. Changes in tray routing directions are made with factory fabricated “L,” “T,” and “X” type tray junctions. Reducer sections come in wider dimensions only where required, building in cost savings. Tray sections can be easily interconnected, using industry common splice washer clamps. M.E.2 trays can be mounted on walls or posts, on ceilings or installed under raised flooring with Cable-Mgr Hardware.

Features and Benefits

  • Field fabricated junctions allow for difficult installations.
  • Seven or 10 foot length straight tray sections can be cut to length or formed by cutting side wires to change routing elevation at the installation site.
  • 2 x 4 inch grid provides easy cable routing in or out of tray sections.
  • Available metal tray divider for cable separation.
  • Rigid steel construction – Made in the USA.
  • Alternative finishes:
    • Hot dip galvanized
    • 304 stainless steel
    • 316L stainless steel

Wire Management Products

The Wiremaid U.S.A. Products Division of Vutec Corporation entered the cable tray arena with the development of PRO-10 and M.E.2 wire cable tray systems.
PRO-10 cable tray
is an innovative and cost-effective system that easily adapts to the most difficult installations. Designed for the low voltage industry and developed with the architect, engineer and installer in mind, PRO-10's pre-fabricated junctions/intersections and ease of installation make it a cost-effective choice of contractors throughout the United States.

M.E.2 cable tray management system is manufactured with rigid .187 diameter zinc-plated steel wire, welded in a two inch by four inch grid facilitating easy cable break outs while supporting the cable. The open grid design prevents dirt build-up and dust experienced in closed cable trays.

PRO-10 Wire Cable Tray

Wiremaid U.S.A. has just created the "Cable Tray Maker,” an easy-to-use cable tray designer that takes the guess work out of ordering a cable tray system. Click on a cable tray part, choose your options and add the quantity. It creates a bill of materials that you can print or email.

• Requires NO bending or cutting; ready–made 4-way, “T” and “L” shaped junctions

• Acts as a continuous ground conductor; no grounding splices

• Adapts to difficult architectural designs to accommodate changes in direction and elevation of cable runs

• Cuts installation time up to 50 percent

• Provides strength, rigidity without additional hardware; has smooth edges

• Manufactured in an array of protective, powder-coated, colored finishes to minimize corrosion

• Featured in light or heavy duty product styles

• All support hardware available

• Powder coating is standard finish

• Custom sizes available

PRO-10 Cable Tray System

M.E.2 Wire Cable Tray

M.E.2 Cable Tray CAD drawings

• Factory fabricated junctions save installation time and cut costs.

• Seven or 10 foot length straight tray sections can be cut to length or formed by cutting side wires to change routing elevation at the installation site.

• Two x 4 inch grid provides easy cable routing in or out of tray sections.

• Available metal tray divider for cable separation.

• Rigid steel construction – Made in the USA.

M.E.2 Cable Tray System

 

 
cisco systems
Telco Systems
Anritsu
Leviton
 
 
 
 
 
 
telecom supply
 
 
 

 

 

 

 

 

 

 

 

 

BIF-Bend Insensitive Fiber

New Bend Insensitive Fiber Jumpers