Fiber
optic Converters- Fiber Optic Converter- Singlemode Converters-Rack Mount Fiber
Optic Media Converters- Fiber Optic Media Converters
American Tech Supply carries the entire line of MRVE1 T1 Fiber Modems, Fiber Optic Converters, Fiber Mux, Fiber Muxes,E1 Fiber Optic Modems, Fiber Optic Media Converters, Singlemode Converters,T1 Fiber Optic Modems, E1T1 Fiber Optic Modems, Fiber Optic Modems. The EM316T1 E1 Fiber Optic Modem and the EM316E1 modules of the Fiber Driver® family are designed to extend the distance and transmission reliability of T1 (1.544Mbps) or E1 (2.048Mbps) traffic. These units convert the electrical signals to optical signals and transmit them over distances of up to 10 km on Multimode fiber, or distances of up to 100 km on Singlemode fiber. The EM316T1 and EM316E1 are transparent to the framing format, and support AMI or B8ZS (T1) and HDB3 (E1) line codes, respectively. They include an internal elastic buffer to remove jitter from the transmitted data. Six LED indicators aid in monitoring and trouble-shooting this module. A management agent is incorporated on the module to enable management in conjunction with the Fiber Driver EM316NM management card. As part of the Fiber Driver family, the EM316T1 and EM316E1 modules fit in all Fiber Driver chassis types, support local and remote loopback tests, and can be used to interconnect between any T1 or E1 devices. Among the types of T1/E1 devices that can be connected by these modules are PBXs, multiplexers, video CODECS, routers, network servers, and ATM/frame relay switches. Benefits include extended distances, improved quality of transmission, better security, remote management capability, and high density applications.
MRV
Communications Small Form-Factor Pluggable (SFP) transceivers
EM316GMX - Gigabit Multimode Extenders
Features
- Allows transmission of Gigabit Ethernet over FDDI-graded Multimode fiber
- Guaranteed distance up to 2 km (Up to 6 km under ideal conditions)
- SNMP managed
- Hot swappable
- Compatible with all appropriate protocol standards
- Fits in all Fiber Driver chassis
The Fiber Driver® Gigabit Multimode Extender applies unique technology that allows the transmission of high-speed signals over Multimode fibers to distances much longer than the standard. This allows the use of high-speed backbone protocols over fiber that was originally used for FDDI.
Fiber optic cables for FDDI applications were typically laid in 2 km increments, since that was the distance limit for FDDI and Fast Ethernet on Multimode fiber. But with today's new high-speed backbone protocols, Multimode fiber's physical characteristics result in a maximum distance of 550 meters,.
The Fiber Driver Gigabit Multimode Extender offes a solution that is interoperable with all standard Gigabit Ethernet equipment. It carries Gigabit Ethernet data on existing Multimode fiber (FDDI graded) to distances of up to 2 km guaranteed. Depending on the quality of the fiber, links of up to 6 km are possible.
The Fiber Driver® Gigabit Multimode Extender applies unique technology that allows the transmission of high-speed signals over Multimode fibers to distances much longer than the standard. This allows the use of high-speed backbone protocols over fiber that was originally used for FDDI.
Fiber optic cables for FDDI applications were typically laid in 2 km increments, since that was the distance limit for FDDI and Fast Ethernet on Multimode fiber. But with today's new high-speed backbone protocols, Multimode fiber's physical characteristics result in a maximum distance of 550 meters,.
The Fiber Driver Gigabit Multimode Extender offes a solution that is interoperable with all standard Gigabit Ethernet equipment. It carries Gigabit Ethernet data on existing Multimode fiber (FDDI graded) to distances of up to 2 km guaranteed. Depending on the quality of the fiber, links of up to 6 km are possible.
MM04 - 4-Port T1 Fiber Optic Media Multiplexer
The MM04 product line is a 4 port E1 or T1 multiplexer/demultiplexer that transmits over a fiber optic link. The products are standalone (1U), 19" rack mountable (half-size devices). The optical fiber interface is available in a number of standard fiber connections and has optional redundant optical connections. The chassis is available with universal AC power supply (100-240v) or DC power supply (36-60v) and and in option of redundant power supply.
MM04 devices support four (4) link interfaces and are available for E1 or T1 configurations with connections for RJ-48 (E1/T1 balanced). In long haul mode the interfaces possess usable receive sensitivity of 0 dB to -43 dB for E1 and 0 dB to -36 dB for T1 which allow the device to operate with 0.63 mm (22AWG) cables at distances up to 2.5 km (E1) and 6000 feet (T1).
MM04
- 4-Port E1 Fiber Optic Media Multiplexer
The MM04 product line is a 4 port E1 or T1 multiplexer/demultiplexer that transmits over a fiber optic link. The products are standalone (1U), 19" rack mountable (half-size devices). The optical fiber interface is available in a number of standard fiber connections and has optional redundant optical connections. The chassis is available with universal AC power supply (100-240v) or DC power supply (36-60v) and and in option of redundant power supply.
MM04 devices support four (4) link interfaces and are available for E1 or T1 configurations with connections for RJ-48 (E1/T1 balanced). In long haul mode the interfaces possess usable receive sensitivity of 0 dB to -43 dB for E1 and 0 dB to -36 dB for T1 which allow the device to operate with 0.63 mm (22AWG) cables at distances up to 2.5 km (E1) and 6000 feet (T1).
Each E1/T1 port is designed to meet regulatory compliant solutions such as for circuit protection against surges and AC lightning, which is essential for long haul E1/T1 lines.
A robust frame-acquisition and frame holding algorithm minimizes frame slippage and resynchronization.
Features
- Complies with: E1/T1 - G.703/G.704
- RJ-48/100 Ohms (T1)
- T1 long haul/limited short haul trunks support
- T1 LEDs are true Receive Carrier Loss (RCL) indication as per G.775
- Completely transparent transmission and and reception
- Fast and easy installation, local indications of local and remote device state
- Small form factor - 1U height, 19" half size width, 30 cm depth
- Redundant power supply - Optional
- Redundant Fiber 1+1 Protection- Optional
- Up to 10 independent dry contact OptoMOS alarm relays - Optional
Applications
The
MM04 product line is a 4 port E1 or T1 multiplexer/demultiplexer that transmits
over a fiber optic link. The products are standalone (1U), 19" rack mountable
(half-size devices). The optical fiber interface is available in a number of standard
fiber connections and has optional redundant optical connections. The chassis
is available with universal AC power supply (100-240v) or DC power supply (36-60v)
and and in option of redundant power supply.
MM04
devices support four (4) link interfaces and are available for E1 or T1 configurations
with connections for RJ-48 (E1/T1 balanced). In long haul mode the interfaces
possess usable receive sensitivity of 0 dB to -43 dB for E1 and 0 dB to -36 dB
for T1 which allow the device to operate with 0.63 mm (22AWG) cables at distances
up to 2.5 km (E1) and 6000 feet (T1).
Each
E1/T1 port is designed to meet regulatory compliant solutions such as for circuit
protection against surges and AC lightning, which is essential for long haul E1/T1
lines
Optical
Protection Switch-EM316OSSH
The
Fiber Driver® Optical Protection Switch from MRV (model number EM316OSSH)
makes creating a redundant optical link easier and more affordable than ever before.
Designed to provide full path protection for mission critical networks, the module
is capable of automatically switching between a primary and secondary (backup)
link in 10 ms or less in the event of a fiber cut or transponder failure.
As
an all optical device performing no optical-electrical-optical (OEO) conversion,
the EM316OSSH remains protocol independent and accepts all wavelengths from 1260
nm to 1630 nm, making it suitable for virtually any application, including WDM
path protection. The module can provide 1+1 protection in resilient point-to-point
or Optical Unidirectional Path Switched Ring (O-UPSR) deployments.
EM316-xSW
- 10/100 Ethernet Switches
The
Fiber Driver® family includes three types of switch modules: three-, four-,
and six-port Ethernet/Fast Ethernet switches. Switch modules are used to link
between 10Mbps and 100Mbps or Half to Full Duplex mode. Switch modules offer a
combination of 10/100Base-TX ports and 100Base-FX ports. They separate between
Ethernet collision domains and filter local traffic from propagating to the rest
of the network.
EM316xSF
- Single Fiber Media Converters
The
Fiber Driver® familys Single Fiber modules use unique technologies,
which provide the ability to combine transmit (TX) and receive (RX) signals onto
a single fiber strand. This effectively doubles the available fiber in a network,
and eliminates the need for additional fiber installation. The Fiber Driver Single
Fiber modules employs Single wavelength bi-directional technology in order to
combine the TX and RX on the single strand.
EM316SC & PASCLCAS - Splitter/Combiner
Splitter/Combiner
technology provides the ability to propagate two signals, transmit (TX) and receive
(RX), over a single fiber strand using the same wavelength. The Fiber Driver® Splitter/Combiner modules, and Splitter/Combiner cables for GBICs and SFPs effectively
double the availability of fiber in a network. They are fully passive devices
that operate at a specific wavelength, and remain protocol and network transparent.
A
pair of Splitter/Combiners add a power loss of only up to 7 dB for SM fiber and
9 dB for MM fiber. Angled Polished Connectors (APCs) are used at the link connections
to eliminate cross-talk.
EM316E1MUX4
- E1 Fiber Multiplexers
The
Fiber Driver® E1 Fiber Multiplexer from MRV Communications transmits four
E1 data channels across a fiber optic trunk in a Point-to-Point (PtP) configuration.
Each line interface consists of a HDB3 encoder/decoder, and a receiver with equalizer
for reliable data and clock recovery. The device also includes a crystal-less
jitter attenuator which, depending on system requirements, can be set in the transmit
(TX) or receive (RX) path. Line distances from 0 to 100m are supported. Line protection
is designed to meet Telecordia GR-1089 standards. The Fiber Driver E1 Fiber Mux
is G.703 interface and G.704 framing compliant.
EM316T1MUX4
- T1 Fiber Multiplexers
The
Fiber Driver® T1 Fiber Multiplexer from MRV Communications transmits four
T1 data channels across a fiber optic trunk in a Point-to-Point (PtP) configuration.
Each line interface consists of a B8ZS, or AMI encoder/decoder as applicable,
and a receiver with equalizer for reliable data and clock recovery. The device
also includes a crystal-less jitter attenuator which, depending on system requirements,
can be set in the transmit (TX) or receive (RX) path. Line distances from 0 to
100 m are supported. Line protection is designed to meet Telecordia GR-1089.
WDM22
E1
/ T1 & Fast/Gigabit Ethernet over a Single Fiber
Combining
Fiber Driver® WDM and Splitter/Combiner technology, the E1 and T1 WDM22 modules
combine separate voice and data channels onto a single strand of fiber. The EM316FE1SF
and EM316GE1SF models merge E1 (2.048Mbs) and Ethernet (100 Mbps and 1000 Mbps
respectively), while the EM316FT1SF and EM316GT1SF combine T1 (1.544Mbs) and Ethernet
(100 Mbps or 1000 Mbps). The units effectively quadruple available fiber capacity.
What would normally require separate dual-fiber links, one for an E1/T1 connection
and one for an Ethernet connection, instead takes only a single strand of fiber.
E1/T1
Fiber Modems
The
EM316T1 and the EM316E1 modules of the Fiber Driver® family are designed to
extend the distance and transmission reliability of T1 (1.544Mbps) or E1 (2.048Mbps)
traffic. These units convert the electrical signals to optical signals and transmit
them over distances of up to 10 km on Multimode fiber, or distances of up to 100
km on Singlemode fiber. The EM316T1 and EM316E1 are transparent to the framing
format, and support AMI or B8ZS (T1) and HDB3 (E1) line codes, respectively
EM316PAMULC,
EM316WP, PAWLCSC - Passive Mux/Demux
2-, 4- and 8-channel modules, and 2-channel
cables
The
Fiber Driver® Passive Mux/Demux module and cables deliver the benefits of
a Wave Division Multiplexer in a fully passive solution. With matching units placed
at each end of an optical link, 2 or more Full Duplex data channels can be combined
and transmitted over a Single Mode fiber trunk.
Rack Mount Media
Converters
"Maxi"
Fiber Optic Mode Converter/Repeater
(Model TC3005) Prices Start at $995.00
ea.
*
Data Rates up to 200 Mbps
* Distances up to 100km
* Local & Remote
Loopback
* Local Dry Contact Alarm Relay
* Test Signal Generator
* 8 Diagnostic LED Indicators
* Built-In Audible Alarm Buzzer
* Built-In
Redundant Power Supply
* Standalone or Rackmount (Interchangeable)
Applications
The
MAXI Mode Converter is used to convert multimode to single mode, or visa versa,
in a variety of LAN and Telephony communication environments including PABX, Ethernet,
Token Ring, FDDI, ATM & SONET (OC1 & OC3). This conversion is done to
cross-connect different fiber types, regenerate optical signals and/or extend
transmission distances.
Description
The
TC3005 "MAXI" Multimode-to-Single Mode Fiber Optic Converter converts
multimode formats to single mode formats, or vice versa, for data transmission
up to 200 Mbps. Transmission distances to more than 100km are possible with the
Laser 1550nm option (34dB loss budget).
The
MAXI will convert or repeat all popular wavelengths including 850nm, 1300nm or
1550nm over single mode or multimode fiber optic cable. It is compatible with
most communication technologies including Ethernet, Token Ring, TAXI, OC1/OC3,
ATM, FDDI and SONET.
The
MAXI provides users with several key features including Local & Remote Loopback,
a Test Signal Generator, Dry Contact Relay Alarm, Audible Alarm Buzzer, Power
Redundancy, and standalone or rackmount modularity.
The
Test Signal Generator and Dry Contact Alarm are particularly beneficial. The Signal
Generator (160 Mbps) helps technicians conduct various installation tests including
fiber link verifications. The Dry Contact Alarm Relay, which includes an audible
alarm buzzer, identifies Optical Signal Loss on either the multimode or single
mode ends.
Power
redundancy is load sharing and switches over automatically in the event of a failure.
Power can be either 12VDC (standard), 24VDC, -48VDC, or 115/230VAC with an external
power cube. Standalone versions are modular, i.e. used either in a standalone
case or in a Rack Mount assembly. Standard connectors are ST or FC type.
Four
DIP switches and eight LED indicators are provided to help installation and troubleshooting.
An extreme temperature version (-20° to 70°C), Model TC3005T, is also
available.
Combination
WDM & Fiber Optic Mode Converter/Repeater
(Model TC3007) Prices Start
at $,1895 ea.
*
Doubles Existing Fiber Cable Capacity
* Converts Multimode to Single Mode
(or Single Mode Repeater)
* Data Rates up to 200 Mbps
* Distances up to
50km
* Local Dry Contact Alarm Relay
* Test Signal Generator & 8 Indicators
* Local & Remote Loopback
* Built-In Audible Alarm Buzzer
* Built-In
Redundant Power Supply
* Standalone or Rackmount (Interchangeable)
Applications
Because
of its multiplexing capability, the TC3007 is often used to increase existing
fiber optic cable capacity in LAN or Telephony environments that require connecting
different fiber types or wavelengths, regenerating optical signals and/or extending
transmission distances. Typical environments include PABX, Ethernet, Fast Ethernet,
Token Ring, FDDI, ATM and SONET (OC1 & OC3).
Description
The
TC3007 Multimode-to-Single Mode Fiber Optic Converter converts multimode formats
to single mode formats, or vice versa, for data transmission up to 200 Mbps. Transmission
distances to more than 50 km are possible with the Laser 1300nm option (25dB loss
budget).The TC3007 functions both as a Fiber Optic Mode Converter/Repeater and
a 2-Channel Wave Division Multiplexer. This benefits users by effectively doubling
existing fiber cable capacity in addition to its mode conversion/repeater functions.The
TC3007 will convert or repeat all popular wavelengths including 850nm, 1300nm
or 1550nm. It is compatible with most communication technologies including Ethernet,
Fast Ethernet, Token Ring, TAXI, OC1/OC3, ATM, FDDI and SONET. It is completely
transparent to incoming data and protocols.
The
TC3007 provides users with several key features including Local/Remote Loopback,
Test Signal Generator, Dry Contact Alarm, Audible Alarm Buzzer, Power Redundancy,
and Standalone or Rack Mount modularity.
The
Test Signal Generator and Dry Contact Alarm are particularly beneficial. The Signal
Generator (160Mbps) helps technicians conduct various installation tests including
fiber link verifications. The Dry Contact Alarm, which includes an audible alarm
buzzer, identifies Optical Signal Loss on either the multimode or single mode
ends.
Power redundancy is load sharing and switches over automatically in
the event of a failure. Power can be either 12VDC, 24VDC, -48VDC, 115/230VAC.
Standalone versions are modular, i.e. used either in a standalone case or in a
rack mount assembly. Standard connectors are ST or FC type. An extreme temperature
version (-20° to 70°C), Model TC3007T, is also available.
A
terminal block connector on the rear panel provides for the dry contact relay
alarm. Normally in the OPEN position, any loss of electrical or optical signal
will trigger an alarm condition and force the switch to the CLOSED position. This
relay can be used in conjunction with an external device to monitor the condition
of the link.
Rack Mount Version
Low
Speed Fiber Optic Mode Converter
(Model TC3020) Prices Start at $1,295.00
ea.
* Supports Burst Data
* Data Rates up to 5 Mbps
* Distances up to 30km*
* Multimode & Single Mode (850/1300/1550nm)
* Multiple Diagnostic LED
Indicators
* Test Signal Generator
* Built-In Loopback Functions
*
Local Dry Contact Alarm Relay
* Stand Alone or Rackmount
Applications
The
TC3020 Mode Converter is frequently used to convert multimode to single mode,
or vice versa, for various low speed devices in SCADA, Automation and Process
Control communication environments. It is also used for Burst Data applications.
This conversion is done to cross-connect different fiber types, regenerate optical
signals and/or extend transmission distance.
Description
Intended
for low speed and Burst Data applications, the TC3020 Multimode-to-Single Mode
Fiber Optic Converter converts multimode formats to single mode formats, or vice
versa, for data transmission up to 5 Mbps.
The
TC3020 is also used to regenerate or extend optical signals. It will convert,
regenerate or extend 850nm, 1300nm or 1550nm wavelengths up to distances of 30
km*.
Eleven
LEDs are provided for diagnostics, monitoring optic signals in both directions
and indicating system status. A Test Signal Generator is available to help technicians
conduct various installation tests including fiber link verifications. A Dry Contact
Relay Alarm is also provided as a standard feature.
The
TC3020 works with all popular types and sizes of fiber optic cable. Fiber optic
connectors are ST or FC type. Power is 12VDC or 115/230VAC with an external power
cube. The TC3020S is a Standalone Unit. The TC3020R is the Rackmount Card Unit
that requires TCRM192 or TCRM196 Rackmount Card Cages. An extreme temperature
version (-20°C to 70°C), Model TC3020T, is also available.
A
terminal block connector on the rear panel provides for the dry contact relay
alarm. Normally in the OPEN position, any loss of electrical or optical signal
will trigger an alarm condition and force the switch to the CLOSED position. This
relay can be used in conjunction with an external device to monitor the condition
of the link.
*Contact factory for higher requirements.