MRV
Fiber Optic Converters-MRV Fiber Optic Media Converter-
MRV Singlemode Media Converters-MRV Media Converters
American Tech
Supply carries the entire line of MRVE1 T1 Fiber Modems,
Fiber Optic Converters, Fiber Mux, Fiber Muxes,E1 Fiber
Optic Modems, Fiber Optic Media Converters, Singlemode Converters,T1
Fiber Optic Modems, E1T1 Fiber Optic Modems, Fiber Optic
Modems. The EM316T1 E1 Fiber Optic Modem and the EM316E1
modules of the Fiber Driver® family are designed to
extend the distance and transmission reliability of T1 (1.544Mbps)
or E1 (2.048Mbps) traffic. These units convert the electrical
signals to optical signals and transmit them over distances
of up to 10 km on Multimode fiber, or distances of up to
100 km on Singlemode fiber. The EM316T1 and EM316E1 are
transparent to the framing format, and support AMI or B8ZS
(T1) and HDB3 (E1) line codes, respectively. They include
an internal elastic buffer to remove jitter from the transmitted
data. Six LED indicators aid in monitoring and trouble-shooting
this module. A management agent is incorporated on the module
to enable management in conjunction with the Fiber Driver
EM316NM management card. As part of the Fiber Driver family,
the EM316T1 and EM316E1 modules fit in all Fiber Driver
chassis types, support local and remote loopback tests,
and can be used to interconnect between any T1 or E1 devices.
Among the types of T1/E1 devices that can be connected by
these modules are PBXs, multiplexers, video CODECS, routers,
network servers, and ATM/frame relay switches. Benefits
include extended distances, improved quality of transmission,
better security, remote management capability, and high
density applications.
MRV
Communications Small Form-Factor Pluggable (SFP) transceivers
MC102Fx
- 10/100Base-TX to 100Base-FX Converters MRV Fiber Optic
Media Converters-The MC102 fiber optic media converter
product line encompasses copper-to-fiber and fiber-to-fiber
conversion units. On all of these fiber optic media converters,
the fiber port(s) allow a choice of multimode or single
mode fiber, single fiber operation, different wavelengths
and power levels.The MC102F/x products are 10/100BaseTX
to 100BaseFX converters, providing external power supply
(MC102F/x) and internal power supply (MC102FI/x) options.
These converters use switching technology for the media
conversion, which provides the necessary packet buffering
and error filtering, forwarding packets up to 1522 bytes.
The copper port on the fiber optic media converter allows
auto-negotiation or can be forced to work at 10Mbps or 100Mbps
via a hardware switch.
-
Converts copper to fiber or Multimode
to Single Mode
-
Compatible with numerous protocol standards,
including Ethernet, SONET, and Fiber Channel
-
Provides distances up to 10km on MM,
130 km on SM
-
Low Temperature option - operating at
a wide temperature range (-45°C to +60°C)
The MC102 MRV fiber optic
media converter product line encompasses copper-to-fiber
and fiber-to-fiber conversion units. On all of these converters,
the fiber port(s) allow a choice of multimode or single
mode fiber, single fiber operation, different wavelengths
and power levels.
The MC102FR is a MRV fiber optic media converter
100BaseFX repeater, targeted for fiber media conversion
(MM to SM), and used for infrastructure adaptation. It is
also used for long distance communications, via repeater
chaining. Since the MC102FR performs 3R (retiming, reshaping,
re-amplification) signal regeneration, units may be placed
one after another without compromising signal quality.
The MC102FRC is a MRV
fiber optic media converter 100BaseTX to 100BaseFX repeater,
targeted for applications requiring long frames (more than
1522 bytes), such as those used by MPLS encapsulation. The
MC102FRC also provides an Automatic Link Integrity (ALI)
feature, which automatically shuts down the copper link
in case of fiber link failure
MC102T MRV fiber optic
media converter protocol transparent media converters
provide media adaptation signal regeneration up to 100Km
for any protocol. Two types of converters are available,
for protocols up to 200Mbps rates (FE, STM1, ESCON, E3,
etc.) and up to 1.25Gbps (GE, FC, STM4).
The MC102G MRV fiber optic media converter products
are 1Gbps signal repeaters for Ethernet or Fiber Channel
(1Gbps) applications. The MC102G units provide fiber-to-fiber
conversion (MM to SM) for infrastructure adaptation. Additionally,
since the MC102G provides 3R signal regeneration, networks
built by chaining these units can reach distances longer
than 100Km without compromising signal quality.
EM316x
- Copper to Fiber Media Converters
Fiber
Driver® copper to fiber media converter modules from
MRV make it easy to merge legacy copper network elements
with new or existing fiber optic infrastructure, allowing
LAN communications to be extended to distances of up to
130 km or more. In addition, the Multimode Extender (MX)
technology found in select Fiber Driver products breaks
the transmission barrier of multimode fiber with link distances
of up to 10 km.
Copper
to multimode and copper to single mode solutions are available
for Ethernet, Fast Ethernet, Gigabit Ethernet and Copper
Gigabit Ethernet, OC-3/STM-1, DS3 and E3. (Additional Ethernet
copper to fiber solution are provided by our signal repeater
and switch modules.
EM316x
- Multimode to Singlemode Media Converters
The
Fiber Driver® collection of Multimode to Single Mode
converters allow network managers to connect between Multimode
and Single Mode fiber. Conversion to Single Mode fiber can
extend the transmission distance to over 100 km. Protocols
covered by this group of modules include SONET OC-3 and
Gigabit Ethernet.
Multimode
to Single Fiber Single Mode modules can be found in the
group of Single Fiber modules.
E1/T1
Fiber Modems
The
EM316T1 and the EM316E1 modules of the Fiber Driver®
family are designed to extend the distance and transmission
reliability of T1 (1.544Mbps) or E1 (2.048Mbps) traffic.
These units convert the electrical signals to optical signals
and transmit them over distances of up to 10 km on Multimode
fiber, or distances of up to 100 km on Singlemode fiber.
The EM316T1 and EM316E1 are transparent to the framing format,
and support AMI or B8ZS (T1) and HDB3 (E1) line codes, respectively.
They include an internal elastic buffer to remove jitter
from the transmitted data. Six LED indicators aid in monitoring
and trouble-shooting this module. A management agent is
incorporated on the module to enable management in conjunction
with the Fiber Driver EM316NM management card. As part of
the Fiber Driver family, the EM316T1 and EM316E1 modules
fit in all Fiber Driver chassis types, support local and
remote loopback tests, and can be used to interconnect between
any T1 or E1 devices. Among the types of T1/E1 devices that
can be connected by these modules are PBXs, multiplexers,
video CODECS, routers, network servers, and ATM/frame relay
switches. Benefits include extended distances, improved
quality of transmission, better security, remote management
capability, and high density.
The
MC102FR is a 100BaseFX repeater, targeted for fiber
media conversion (MM to SM), and used for infrastructure
adaptation. It is also used for long distance communications,
via repeater chaining. Since the MC102FR performs 3R (retiming,
reshaping, re-amplification) signal regeneration, units
may be placed one after another without compromising signal
quality.
The
MC102FRC is a 100BaseTX to 100BaseFX repeater, targeted
for applications requiring long frames (more than 1522 bytes),
such as those used by MPLS encapsulation. The MC102FRC also
provides an Automatic Link Integrity (ALI) feature, which
automatically shuts down the copper link in case of fiber
link failure.
MC102T
Fiber Optic Media Converter protocol transparent media converters
provide media adaptation signal regeneration up to 100Km
for any protocol. Two types of converters are available,
for protocols up to 200Mbps rates (FE, STM1, ESCON, E3,
etc.) and up to 1.25Gbps (GE, FC, STM4).
The
MC102G Fiber Optic Media Converter products
are 1Gbps signal repeaters for Ethernet or Fiber Channel
(1Gbps) applications. The MC102G units provide fiber-to-fiber
conversion (MM to SM) for infrastructure adaptation. Additionally,
since the MC102G provides 3R signal regeneration, networks
built by chaining these units can reach distances longer
than 100Km without compromising signal quality.
MS104
- Unmanaged 4-Port Ethernet Fiber Optic Switches
The
MS104 products are 4-port switches, which are targeted for
SOHO, FTTH, and other applications where a few 10/100BaseTX
devices need to be concentrated and connected to the network
by fiber connections. The family members differ from each
other by the type of fiber optic ports connection they accommodate,
with a choice of multimode fiber, singlemode fiber, single
fiber operation, different wavelengths and power levels
as well as different connector types (DSC, SC and MTRJ).
MS105
- Unmanaged 5-Port Ethernet Fiber Optic Switches
The
MS105 products are 5-port switches, which are targeted for
SOHO, FTTH, and other applications where a few 10/100BaseTX
devices need to be concentrated and connected to the network
by fiber connections. The family members differ from each
other by the type of fiber optic ports connection they accommodate,
with a choice of multimode fiber, singlemode fiber, single
fiber operation, different wavelengths and power levels
as well as different connector types (DSC, SC and MTRJ).
MM04
- 4-Port E1 Fiber Optic Media Multiplexer
The
MM04 product line is a 4 port E1 or T1 multiplexer/demultiplexer
that transmits over a fiber optic link. The products are
standalone (1U), 19" rack mountable (half-size devices).
The optical fiber interface is available in a number of
standard fiber connections and has optional redundant optical
connections. The chassis is available with universal AC
power supply (100-240v) or DC power supply (36-60v) and
and in option of redundant power supply.
MM04
devices support four (4) link interfaces and are available
for E1 or T1 configurations with connections for RJ-48 (E1/T1
balanced). In long haul mode the interfaces possess usable
receive sensitivity of 0 dB to -43 dB for E1 and 0 dB to
-36 dB for T1 which allow the device to operate with 0.63
mm (22AWG) cables at distances up to 2.5 km (E1) and 6000
feet (T1).
Each
E1/T1 port is designed to meet regulatory compliant solutions
such as for circuit protection against surges and AC lightning,
which is essential for long haul E1/T1 lines
MM04
- 4-Port T1 Fiber Optic Media Multiplexer
The
MM04 product line is a 4 port E1 or T1 multiplexer/demultiplexer
that transmits over a fiber optic link. The products are
standalone (1U), 19" rack mountable (half-size devices).
The optical fiber interface is available in a number of
standard fiber connections and has optional redundant optical
connections. The chassis is available with universal AC
power supply (100-240v) or DC power supply (36-60v) and
and in option of redundant power supply.
MM04
devices support four (4) link interfaces and are available
for E1 or T1 configurations with connections for RJ-48 (E1/T1
balanced). In long haul mode the interfaces possess usable
receive sensitivity of 0 dB to -43 dB for E1 and 0 dB to
-36 dB for T1 which allow the device to operate with 0.63
mm (22AWG) cables at distances up to 2.5 km (E1) and 6000
feet (T1).
EM316GMX
- Gigabit Multimode Extenders
The
Fiber Driver® Gigabit Multimode Extender applies unique
technology that allows the transmission of high-speed signals
over Multimode fibers to distances much longer than the
standard. This allows the use of high-speed backbone protocols
over fiber that was originally used for FDDI.
Fiber
optic cables for FDDI applications were typically laid in
2 km increments, since that was the distance limit for FDDI
and Fast Ethernet on Multimode fiber. But with today's new
high-speed backbone protocols, Multimode fiber's physical
characteristics result in a maximum distance of 550 meters,.
The
Fiber Driver Gigabit Multimode Extender offes a solution
that is interoperable with all standard Gigabit Ethernet
equipment. It carries Gigabit Ethernet data on existing
Multimode fiber (FDDI graded) to distances of up to 2 km
guaranteed. Depending on the quality of the fiber, links
of up to 6 km are possible.
Optical
Protection Switch-EM316OSSH
The
Fiber Driver® Optical Protection Switch from MRV (model
number EM316OSSH) makes creating a redundant optical link
easier and more affordable than ever before. Designed to
provide full path protection for mission critical networks,
the module is capable of automatically switching between
a primary and secondary (backup) link in 10 ms or less in
the event of a fiber cut or transponder failure.
As
an all optical device performing no optical-electrical-optical
(OEO) conversion, the EM316OSSH remains protocol independent
and accepts all wavelengths from 1260 nm to 1630 nm, making
it suitable for virtually any application, including WDM
path protection. The module can provide 1+1 protection in
resilient point-to-point or Optical Unidirectional Path
Switched Ring (O-UPSR) deployments.
EM316-xSW
- 10/100 Ethernet Switches
The
Fiber Driver® family includes three types of switch
modules: three-, four-, and six-port Ethernet/Fast Ethernet
switches. Switch modules are used to link between 10Mbps
and 100Mbps or Half to Full Duplex mode. Switch modules
offer a combination of 10/100Base-TX ports and 100Base-FX
ports. They separate between Ethernet collision domains
and filter local traffic from propagating to the rest of
the network.
EM316xSF
- Single Fiber Media Converters
The
Fiber Driver® familys Single Fiber modules use
unique technologies, which provide the ability to combine
transmit (TX) and receive (RX) signals onto a single fiber
strand. This effectively doubles the available fiber in
a network, and eliminates the need for additional fiber
installation. The Fiber Driver Single Fiber modules employs
Single wavelength bi-directional technology in order to
combine the TX and RX on the single strand.
EM316SC
& PASCLCAS - Splitter/Combiner
Splitter/Combiner
technology provides the ability to propagate two signals,
transmit (TX) and receive (RX), over a single fiber strand
using the same wavelength. The Fiber Driver® Splitter/Combiner
modules, and Splitter/Combiner cables for GBICs and SFPs
effectively double the availability of fiber in a network.
They are fully passive devices that operate at a specific
wavelength, and remain protocol and network transparent.
A
pair of Splitter/Combiners add a power loss of only up to
7 dB for SM fiber and 9 dB for MM fiber. Angled Polished
Connectors (APCs) are used at the link connections to eliminate
cross-talk.
EM316E1MUX4
- E1 Fiber Multiplexers
The
Fiber Driver® E1 Fiber Multiplexer from MRV Communications
transmits four E1 data channels across a fiber optic trunk
in a Point-to-Point (PtP) configuration. Each line interface
consists of a HDB3 encoder/decoder, and a receiver with
equalizer for reliable data and clock recovery. The device
also includes a crystal-less jitter attenuator which, depending
on system requirements, can be set in the transmit (TX)
or receive (RX) path. Line distances from 0 to 100m are
supported. Line protection is designed to meet Telecordia
GR-1089 standards. The Fiber Driver E1 Fiber Mux is G.703
interface and G.704 framing compliant.
EM316T1MUX4
- T1 Fiber Multiplexers
The
Fiber Driver® T1 Fiber Multiplexer from MRV Communications
transmits four T1 data channels across a fiber optic trunk
in a Point-to-Point (PtP) configuration. Each line interface
consists of a B8ZS, or AMI encoder/decoder as applicable,
and a receiver with equalizer for reliable data and clock
recovery. The device also includes a crystal-less jitter
attenuator which, depending on system requirements, can
be set in the transmit (TX) or receive (RX) path. Line distances
from 0 to 100 m are supported. Line protection is designed
to meet Telecordia GR-1089.
WDM22
E1 / T1 & Fast/Gigabit Ethernet over a Single Fiber
Combining
Fiber Driver® WDM and Splitter/Combiner technology,
the E1 and T1 WDM22 modules combine separate voice and data
channels onto a single strand of fiber. The EM316FE1SF and
EM316GE1SF models merge E1 (2.048Mbs) and Ethernet (100
Mbps and 1000 Mbps respectively), while the EM316FT1SF and
EM316GT1SF combine T1 (1.544Mbs) and Ethernet (100 Mbps
or 1000 Mbps). The units effectively quadruple available
fiber capacity. What would normally require separate dual-fiber
links, one for an E1/T1 connection and one for an Ethernet
connection, instead takes only a single strand of fiber.
E1/T1
Fiber Modems
The
EM316T1 and the EM316E1 modules of the Fiber Driver®
family are designed to extend the distance and transmission
reliability of T1 (1.544Mbps) or E1 (2.048Mbps) traffic.
These units convert the electrical signals to optical signals
and transmit them over distances of up to 10 km on Multimode
fiber, or distances of up to 100 km on Singlemode fiber.
The EM316T1 and EM316E1 are transparent to the framing format,
and support AMI or B8ZS (T1) and HDB3 (E1) line codes, respectively
EM316PAMULC,
EM316WP, PAWLCSC - Passive Mux/Demux
2-, 4- and 8-channel modules, and 2-channel cables
The
Fiber Driver® Passive Mux/Demux module and cables deliver
the benefits of a Wave Division Multiplexer in a fully passive
solution. With matching units placed at each end of an optical
link, 2 or more Full Duplex data channels can be combined
and transmitted over a Single Mode fiber trunk.
Rack Mount Media Converters
"Maxi"
Fiber Optic Mode Converter/Repeater
(Model TC3005) Prices Start at $995.00 ea.
*
Data Rates up to 200 Mbps
* Distances up to 100km
* Local & Remote Loopback
* Local Dry Contact Alarm Relay
* Test Signal Generator
* 8 Diagnostic LED Indicators
* Built-In Audible Alarm Buzzer
* Built-In Redundant Power Supply
* Standalone or Rackmount (Interchangeable)
Applications
The
MAXI Mode Converter is used to convert multimode to single
mode, or visa versa, in a variety of LAN and Telephony communication
environments including PABX, Ethernet, Token Ring, FDDI,
ATM & SONET (OC1 & OC3). This conversion is done
to cross-connect different fiber types, regenerate optical
signals and/or extend transmission distances.
Description
The
TC3005 "MAXI" Multimode-to-Single Mode Fiber Optic
Converter converts multimode formats to single mode formats,
or vice versa, for data transmission up to 200 Mbps. Transmission
distances to more than 100km are possible with the Laser
1550nm option (34dB loss budget).
The
MAXI will convert or repeat all popular wavelengths including
850nm, 1300nm or 1550nm over single mode or multimode fiber
optic cable. It is compatible with most communication technologies
including Ethernet, Token Ring, TAXI, OC1/OC3, ATM, FDDI
and SONET.
The
MAXI provides users with several key features including
Local & Remote Loopback, a Test Signal Generator, Dry
Contact Relay Alarm, Audible Alarm Buzzer, Power Redundancy,
and standalone or rackmount modularity.
The
Test Signal Generator and Dry Contact Alarm are particularly
beneficial. The Signal Generator (160 Mbps) helps technicians
conduct various installation tests including fiber link
verifications. The Dry Contact Alarm Relay, which includes
an audible alarm buzzer, identifies Optical Signal Loss
on either the multimode or single mode ends.
Power
redundancy is load sharing and switches over automatically
in the event of a failure. Power can be either 12VDC (standard),
24VDC, -48VDC, or 115/230VAC with an external power cube.
Standalone versions are modular, i.e. used either in a standalone
case or in a Rack Mount assembly. Standard connectors are
ST or FC type.
Four
DIP switches and eight LED indicators are provided to help
installation and troubleshooting. An extreme temperature
version (-20° to 70°C), Model TC3005T, is also available.
Combination
WDM & Fiber Optic Mode Converter/Repeater
(Model TC3007) Prices Start at $,1895 ea.
*
Doubles Existing Fiber Cable Capacity
* Converts Multimode to Single Mode (or Single Mode Repeater)
* Data Rates up to 200 Mbps
* Distances up to 50km
* Local Dry Contact Alarm Relay
* Test Signal Generator & 8 Indicators
* Local & Remote Loopback
* Built-In Audible Alarm Buzzer
* Built-In Redundant Power Supply
* Standalone or Rackmount (Interchangeable)
Applications
Because
of its multiplexing capability, the TC3007 is often used
to increase existing fiber optic cable capacity in LAN or
Telephony environments that require connecting different
fiber types or wavelengths, regenerating optical signals
and/or extending transmission distances. Typical environments
include PABX, Ethernet, Fast Ethernet, Token Ring, FDDI,
ATM and SONET (OC1 & OC3).
Description
The
TC3007 Multimode-to-Single Mode Fiber Optic Converter converts
multimode formats to single mode formats, or vice versa,
for data transmission up to 200 Mbps. Transmission distances
to more than 50 km are possible with the Laser 1300nm option
(25dB loss budget).The TC3007 functions both as a Fiber
Optic Mode Converter/Repeater and a 2-Channel Wave Division
Multiplexer. This benefits users by effectively doubling
existing fiber cable capacity in addition to its mode conversion/repeater
functions.The TC3007 will convert or repeat all popular
wavelengths including 850nm, 1300nm or 1550nm. It is compatible
with most communication technologies including Ethernet,
Fast Ethernet, Token Ring, TAXI, OC1/OC3, ATM, FDDI and
SONET. It is completely transparent to incoming data and
protocols.
The
TC3007 provides users with several key features including
Local/Remote Loopback, Test Signal Generator, Dry Contact
Alarm, Audible Alarm Buzzer, Power Redundancy, and Standalone
or Rack Mount modularity.
The
Test Signal Generator and Dry Contact Alarm are particularly
beneficial. The Signal Generator (160Mbps) helps technicians
conduct various installation tests including fiber link
verifications. The Dry Contact Alarm, which includes an
audible alarm buzzer, identifies Optical Signal Loss on
either the multimode or single mode ends.
Power redundancy is load sharing and switches over automatically
in the event of a failure. Power can be either 12VDC, 24VDC,
-48VDC, 115/230VAC. Standalone versions are modular, i.e.
used either in a standalone case or in a rack mount assembly.
Standard connectors are ST or FC type. An extreme temperature
version (-20° to 70°C), Model TC3007T, is also available.
A
terminal block connector on the rear panel provides for
the dry contact relay alarm. Normally in the OPEN position,
any loss of electrical or optical signal will trigger an
alarm condition and force the switch to the CLOSED position.
This relay can be used in conjunction with an external device
to monitor the condition of the link.
Rack
Mount Version
Low
Speed Fiber Optic Mode Converter
(Model TC3020) Prices Start at $1,295.00 ea.
* Supports Burst Data
* Data Rates up to 5 Mbps
* Distances up to 30km*
* Multimode & Single Mode (850/1300/1550nm)
* Multiple Diagnostic LED Indicators
* Test Signal Generator
* Built-In Loopback Functions
* Local Dry Contact Alarm Relay
* Stand Alone or Rackmount
Applications
The
TC3020 Mode Converter is frequently used to convert multimode
to single mode, or vice versa, for various low speed devices
in SCADA, Automation and Process Control communication environments.
It is also used for Burst Data applications. This conversion
is done to cross-connect different fiber types, regenerate
optical signals and/or extend transmission distance.
Description
Intended
for low speed and Burst Data applications, the TC3020 Multimode-to-Single
Mode Fiber Optic Converter converts multimode formats to
single mode formats, or vice versa, for data transmission
up to 5 Mbps.
The
TC3020 is also used to regenerate or extend optical signals.
It will convert, regenerate or extend 850nm, 1300nm or 1550nm
wavelengths up to distances of 30 km*.
Eleven
LEDs are provided for diagnostics, monitoring optic signals
in both directions and indicating system status. A Test
Signal Generator is available to help technicians conduct
various installation tests including fiber link verifications.
A Dry Contact Relay Alarm is also provided as a standard
feature.
The
TC3020 works with all popular types and sizes of fiber optic
cable. Fiber optic connectors are ST or FC type. Power is
12VDC or 115/230VAC with an external power cube. The TC3020S
is a Standalone Unit. The TC3020R is the Rackmount Card
Unit that requires TCRM192 or TCRM196 Rackmount Card Cages.
An extreme temperature version (-20°C to 70°C),
Model TC3020T, is also available.
A
terminal block connector on the rear panel provides for
the dry contact relay alarm. Normally in the OPEN position,
any loss of electrical or optical signal will trigger an
alarm condition and force the switch to the CLOSED position.
This relay can be used in conjunction with an external device
to monitor the condition of the link.
*Contact factory for higher requirements.
Description
TC3210R/S Fiber Optic Media Converter
Featuring
connectivity distances up to 100km, the TC3210R/S Media
Converter converts or connects 10/100Mbps Ethernet Unshielded
Twisted Pair (10/100Base-T) to single mode or multimode
fiber optics (10/100Base-FX). It is commonly used to interconnect
network bridges, hubs, or workstation cards. The TC3210S
is the standalone/wallmount unit. The TC3210R rackmount
version fits into TCRM192 or TCRM196 19" rackmount
card cages.
Completely
transparent to the network, the TC3210R/S is ideal for integrating
UTP and fiber optics in any Fast Ethernet network. Designed
with modern Field Programmable Gate Array (FPGA) technology,
it operates efficiently even during high-demand traffic
loads.
Dry
contact alarms are provided for connection to remote network
management systems. A local fiber loopback feature, eight
LED indicators, and an Uplink/Downlink slide switch are
provided on the front panel to assist in installation &
troubleshooting.
The
TC3210R/S is available both multimode (1300nm) and single
mode (1300nm & 1550nm). Fiber optic connectors are ST
or FC. The UTP connector is RJ-45 female. Power is 12VDC
@ 600mA (standard); optional power sources include 24VDC,
-48VDC, 125VDC, or 115/230VAC with an external power cube.
An extreme temperature version (-20° to 70°C, -40°
to 80°C), Model TC3210X, is also available.
A
terminal block connector on the rear panel provides for
the dry contact relay alarm. Normally in the OPEN position,
any loss of electrical or optical signal will trigger an
alarm condition and force the switch to the CLOSED position.
This relay can be used in conjunction with an external device
to monitor the condition of the link.