Discontinued Products
Showing 7129–7152 of 10717 results
-
Discontinued Products
ABS Plastic Hand Held Enclosures RH Series – (RH3045) (DISCONTINUED)
Key Features:
- Electronic hand held enclosures, ideally suited for mounting printed circuit boards.
- Ergonomically designed for a comfortable fit into the user’s hand.
- Lap joint construction provides protection against dust accumulation and splashing water.
- Available in two versions – gasketed (IP65 rated) & no gasket.
- Gasketed version includes gasket around top & bottom half and around battery door (factory installed).
- Molded in a general purpose ABS plastic with a light texture (material carries a UL flammability rating of UL94 HB).
- The top half includes a smooth recessed area for membrane, label or silkscreen.
- Assembled with M3 Philips self tapping screws.
- Both top and bottom halves contain P.C. board standoffs molded in (see photos for details).
Photos:
Belt Clips:
- Choice of either black or grey (to match above enclosures)
- Made from tough nylon material
- Includes mounting hardware
- Black – Part Number CP-001BK
- Grey – Part Number CP-001G.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
SKU: RH3045 -
Discontinued Products
ABS Plastic Hand Held Enclosures RH Series – (RH3055) (DISCONTINUED)
Key Features:
- Electronic hand held enclosures, ideally suited for mounting printed circuit boards.
- Ergonomically designed for a comfortable fit into the user’s hand.
- Lap joint construction provides protection against dust accumulation and splashing water.
- Available in two versions – gasketed (IP65 rated) & no gasket.
- Gasketed version includes gasket around top & bottom half and around battery door (factory installed).
- Molded in a general purpose ABS plastic with a light texture (material carries a UL flammability rating of UL94 HB).
- The top half includes a smooth recessed area for membrane, label or silkscreen.
- Assembled with M3 Philips self tapping screws.
- Both top and bottom halves contain P.C. board standoffs molded in (see photos for details).
Photos:
Belt Clips:
- Choice of either black or grey (to match above enclosures)
- Made from tough nylon material
- Includes mounting hardware
- Black – Part Number CP-001BK
- Grey – Part Number CP-001G.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
SKU: RH3055 -
Discontinued Products
ABS Plastic Hand Held Enclosures RH Series – (RH3005) (DISCONTINUED)
Key Features:
- Electronic hand held enclosures, ideally suited for mounting printed circuit boards.
- Ergonomically designed for a comfortable fit into the user’s hand.
- Lap joint construction provides protection against dust accumulation and splashing water.
- Available in two versions – gasketed (IP65 rated) & no gasket.
- Gasketed version includes gasket around top & bottom half and around battery door (factory installed).
- Molded in a general purpose ABS plastic with a light texture (material carries a UL flammability rating of UL94 HB).
- The top half includes a smooth recessed area for membrane, label or silkscreen.
- Assembled with M3 Philips self tapping screws.
- Both top and bottom halves contain P.C. board standoffs molded in (see photos for details).
Photos:
Belt Clips:
- Choice of either black or grey (to match above enclosures)
- Made from tough nylon material
- Includes mounting hardware
- Black – Part Number CP-001BK
- Grey – Part Number CP-001G.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
SKU: RH3005 -
Discontinued Products
ABS Plastic Hand Held Enclosures RH Series – (RH3015) (DISCONTINUED)
Key Features:
- Electronic hand held enclosures, ideally suited for mounting printed circuit boards.
- Ergonomically designed for a comfortable fit into the user’s hand.
- Lap joint construction provides protection against dust accumulation and splashing water.
- Available in two versions – gasketed (IP65 rated) & no gasket.
- Gasketed version includes gasket around top & bottom half and around battery door (factory installed).
- Molded in a general purpose ABS plastic with a light texture (material carries a UL flammability rating of UL94 HB).
- The top half includes a smooth recessed area for membrane, label or silkscreen.
- Assembled with M3 Philips self tapping screws.
- Both top and bottom halves contain P.C. board standoffs molded in (see photos for details).
Photos:
Belt Clips:
- Choice of either black or grey (to match above enclosures)
- Made from tough nylon material
- Includes mounting hardware
- Black – Part Number CP-001BK
- Grey – Part Number CP-001G.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
SKU: RH3015 -
Discontinued Products
ABS Plastic Hand Held Enclosures RH Series – (RH3045BK) (DISCONTINUED)
Key Features:
- Electronic hand held enclosures, ideally suited for mounting printed circuit boards.
- Ergonomically designed for a comfortable fit into the user’s hand.
- Lap joint construction provides protection against dust accumulation and splashing water.
- Available in two versions – gasketed (IP65 rated) & no gasket.
- Gasketed version includes gasket around top & bottom half and around battery door (factory installed).
- Molded in a general purpose ABS plastic with a light texture (material carries a UL flammability rating of UL94 HB).
- The top half includes a smooth recessed area for membrane, label or silkscreen.
- Assembled with M3 Philips self tapping screws.
- Both top and bottom halves contain P.C. board standoffs molded in (see photos for details).
Photos:
Belt Clips:
- Choice of either black or grey (to match above enclosures)
- Made from tough nylon material
- Includes mounting hardware
- Black – Part Number CP-001BK
- Grey – Part Number CP-001G.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
SKU: RH3045BK -
Discontinued Products
ABS Plastic Hand Held Enclosures RH Series – (RH3051BK) (DISCONTINUED)
Key Features:
- Electronic hand held enclosures, ideally suited for mounting printed circuit boards.
- Ergonomically designed for a comfortable fit into the user’s hand.
- Lap joint construction provides protection against dust accumulation and splashing water.
- Available in two versions – gasketed (IP65 rated) & no gasket.
- Gasketed version includes gasket around top & bottom half and around battery door (factory installed).
- Molded in a general purpose ABS plastic with a light texture (material carries a UL flammability rating of UL94 HB).
- The top half includes a smooth recessed area for membrane, label or silkscreen.
- Assembled with M3 Philips self tapping screws.
- Both top and bottom halves contain P.C. board standoffs molded in (see photos for details).
Photos:
Belt Clips:
- Choice of either black or grey (to match above enclosures)
- Made from tough nylon material
- Includes mounting hardware
- Black – Part Number CP-001BK
- Grey – Part Number CP-001G.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
SKU: RH3051BK -
Discontinued Products
ABS Plastic Hand Held Enclosures RH Series – (RH3001BK) (DISCONTINUED)
Key Features:
- Electronic hand held enclosures, ideally suited for mounting printed circuit boards.
- Ergonomically designed for a comfortable fit into the user’s hand.
- Lap joint construction provides protection against dust accumulation and splashing water.
- Available in two versions – gasketed (IP65 rated) & no gasket.
- Gasketed version includes gasket around top & bottom half and around battery door (factory installed).
- Molded in a general purpose ABS plastic with a light texture (material carries a UL flammability rating of UL94 HB).
- The top half includes a smooth recessed area for membrane, label or silkscreen.
- Assembled with M3 Philips self tapping screws.
- Both top and bottom halves contain P.C. board standoffs molded in (see photos for details).
Photos:
Belt Clips:
- Choice of either black or grey (to match above enclosures)
- Made from tough nylon material
- Includes mounting hardware
- Black – Part Number CP-001BK
- Grey – Part Number CP-001G.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
SKU: RH3001BK -
Discontinued Products
ABS Plastic Hand Held Enclosures RH Series – (RH3011BK) (DISCONTINUED)
Key Features:
- Electronic hand held enclosures, ideally suited for mounting printed circuit boards.
- Ergonomically designed for a comfortable fit into the user’s hand.
- Lap joint construction provides protection against dust accumulation and splashing water.
- Available in two versions – gasketed (IP65 rated) & no gasket.
- Gasketed version includes gasket around top & bottom half and around battery door (factory installed).
- Molded in a general purpose ABS plastic with a light texture (material carries a UL flammability rating of UL94 HB).
- The top half includes a smooth recessed area for membrane, label or silkscreen.
- Assembled with M3 Philips self tapping screws.
- Both top and bottom halves contain P.C. board standoffs molded in (see photos for details).
Photos:
Belt Clips:
- Choice of either black or grey (to match above enclosures)
- Made from tough nylon material
- Includes mounting hardware
- Black – Part Number CP-001BK
- Grey – Part Number CP-001G.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
SKU: RH3011BK -
Discontinued Products
Water-Tight ABS Plastic R220 Series – (R220-104-000) (DISCONTINUED)
Key Information:
Application
- ABS plastic enclosures are designed for use as instrument enclosures, electrical junction boxes or terminal wiring enclosures where metallic enclosures are not suitable.
- Modern design with slanted top edges.
- Provide outstanding protection against dust, oil and pressurized water.
- Impervious to atmospheric and marine corrosion.
Standards
- NEMA Type 4, 4X, 12 and 13
- IP66
- UL94 HB Flammability Rating
Construction
- Molded in ABS plastic.
- Separate mounting channels & lid channels.
- Recessed polyurethane gasket with tongue and groove construction.
- Interlocking flange on lid and bottom sections.
- Captive stainless steel lid screws are provided.
- Cover screws fasten into pre-threaded holes.
Finish
- Light grey RAL 7035
- Separate screw channels outside of the gasket seal (lid screws & enclosure mounting screws).
- There are many mounting posts for self tapping screws in both the enclosure & the lid. Can also be used for mounting P.C. boards or plates.
- Thermoplastic forpene gasket.
- Enclosure mounts through channel and bottom holes, concealed when lid is attached.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: mm. Switch units to: inch
Part No. Length Width Height R220-060-000 66 51 35 R220-080-000 83 81 60 R220-082-000 121 81 60 R220-084-000 161 81 60 R220-102-000 151 101 60 R220-104-000 201 101 60 R220-120-000 123 121 80 R220-122-000 201 121 80 R220-160-000 161 161 80 R220-162-000 241 161 80 SKU: R220-104-000 -
Discontinued Products
Water-Tight ABS Plastic R220 Series – (R220-102-000) (DISCONTINUED)
Key Information:
Application
- ABS plastic enclosures are designed for use as instrument enclosures, electrical junction boxes or terminal wiring enclosures where metallic enclosures are not suitable.
- Modern design with slanted top edges.
- Provide outstanding protection against dust, oil and pressurized water.
- Impervious to atmospheric and marine corrosion.
Standards
- NEMA Type 4, 4X, 12 and 13
- IP66
- UL94 HB Flammability Rating
Construction
- Molded in ABS plastic.
- Separate mounting channels & lid channels.
- Recessed polyurethane gasket with tongue and groove construction.
- Interlocking flange on lid and bottom sections.
- Captive stainless steel lid screws are provided.
- Cover screws fasten into pre-threaded holes.
Finish
- Light grey RAL 7035
- Separate screw channels outside of the gasket seal (lid screws & enclosure mounting screws).
- There are many mounting posts for self tapping screws in both the enclosure & the lid. Can also be used for mounting P.C. boards or plates.
- Thermoplastic forpene gasket.
- Enclosure mounts through channel and bottom holes, concealed when lid is attached.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: mm. Switch units to: inch
Part No. Length Width Height R220-060-000 66 51 35 R220-080-000 83 81 60 R220-082-000 121 81 60 R220-084-000 161 81 60 R220-102-000 151 101 60 R220-104-000 201 101 60 R220-120-000 123 121 80 R220-122-000 201 121 80 R220-160-000 161 161 80 R220-162-000 241 161 80 SKU: R220-102-000 -
Discontinued Products
Water-Tight ABS Plastic R220 Series – (R220-084-000) (DISCONTINUED)
Key Information:
Application
- ABS plastic enclosures are designed for use as instrument enclosures, electrical junction boxes or terminal wiring enclosures where metallic enclosures are not suitable.
- Modern design with slanted top edges.
- Provide outstanding protection against dust, oil and pressurized water.
- Impervious to atmospheric and marine corrosion.
Standards
- NEMA Type 4, 4X, 12 and 13
- IP66
- UL94 HB Flammability Rating
Construction
- Molded in ABS plastic.
- Separate mounting channels & lid channels.
- Recessed polyurethane gasket with tongue and groove construction.
- Interlocking flange on lid and bottom sections.
- Captive stainless steel lid screws are provided.
- Cover screws fasten into pre-threaded holes.
Finish
- Light grey RAL 7035
- Separate screw channels outside of the gasket seal (lid screws & enclosure mounting screws).
- There are many mounting posts for self tapping screws in both the enclosure & the lid. Can also be used for mounting P.C. boards or plates.
- Thermoplastic forpene gasket.
- Enclosure mounts through channel and bottom holes, concealed when lid is attached.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: mm. Switch units to: inch
Part No. Length Width Height R220-060-000 66 51 35 R220-080-000 83 81 60 R220-082-000 121 81 60 R220-084-000 161 81 60 R220-102-000 151 101 60 R220-104-000 201 101 60 R220-120-000 123 121 80 R220-122-000 201 121 80 R220-160-000 161 161 80 R220-162-000 241 161 80 SKU: R220-084-000 -
Discontinued Products
Water-Tight ABS Plastic R220 Series – (R220-082-000) (DISCONTINUED)
Key Information:
Application
- ABS plastic enclosures are designed for use as instrument enclosures, electrical junction boxes or terminal wiring enclosures where metallic enclosures are not suitable.
- Modern design with slanted top edges.
- Provide outstanding protection against dust, oil and pressurized water.
- Impervious to atmospheric and marine corrosion.
Standards
- NEMA Type 4, 4X, 12 and 13
- IP66
- UL94 HB Flammability Rating
Construction
- Molded in ABS plastic.
- Separate mounting channels & lid channels.
- Recessed polyurethane gasket with tongue and groove construction.
- Interlocking flange on lid and bottom sections.
- Captive stainless steel lid screws are provided.
- Cover screws fasten into pre-threaded holes.
Finish
- Light grey RAL 7035
- Separate screw channels outside of the gasket seal (lid screws & enclosure mounting screws).
- There are many mounting posts for self tapping screws in both the enclosure & the lid. Can also be used for mounting P.C. boards or plates.
- Thermoplastic forpene gasket.
- Enclosure mounts through channel and bottom holes, concealed when lid is attached.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: mm. Switch units to: inch
Part No. Length Width Height R220-060-000 66 51 35 R220-080-000 83 81 60 R220-082-000 121 81 60 R220-084-000 161 81 60 R220-102-000 151 101 60 R220-104-000 201 101 60 R220-120-000 123 121 80 R220-122-000 201 121 80 R220-160-000 161 161 80 R220-162-000 241 161 80 SKU: R220-082-000 -
Discontinued Products
Water-Tight ABS Plastic R220 Series – (R220-080-000) (DISCONTINUED)
Key Information:
Application
- ABS plastic enclosures are designed for use as instrument enclosures, electrical junction boxes or terminal wiring enclosures where metallic enclosures are not suitable.
- Modern design with slanted top edges.
- Provide outstanding protection against dust, oil and pressurized water.
- Impervious to atmospheric and marine corrosion.
Standards
- NEMA Type 4, 4X, 12 and 13
- IP66
- UL94 HB Flammability Rating
Construction
- Molded in ABS plastic.
- Separate mounting channels & lid channels.
- Recessed polyurethane gasket with tongue and groove construction.
- Interlocking flange on lid and bottom sections.
- Captive stainless steel lid screws are provided.
- Cover screws fasten into pre-threaded holes.
Finish
- Light grey RAL 7035
- Separate screw channels outside of the gasket seal (lid screws & enclosure mounting screws).
- There are many mounting posts for self tapping screws in both the enclosure & the lid. Can also be used for mounting P.C. boards or plates.
- Thermoplastic forpene gasket.
- Enclosure mounts through channel and bottom holes, concealed when lid is attached.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: mm. Switch units to: inch
Part No. Length Width Height R220-060-000 66 51 35 R220-080-000 83 81 60 R220-082-000 121 81 60 R220-084-000 161 81 60 R220-102-000 151 101 60 R220-104-000 201 101 60 R220-120-000 123 121 80 R220-122-000 201 121 80 R220-160-000 161 161 80 R220-162-000 241 161 80 SKU: R220-080-000 -
Discontinued Products
Water-Tight ABS Plastic R220 Series – (R220-060-000) (DISCONTINUED)
Key Information:
Application
- ABS plastic enclosures are designed for use as instrument enclosures, electrical junction boxes or terminal wiring enclosures where metallic enclosures are not suitable.
- Modern design with slanted top edges.
- Provide outstanding protection against dust, oil and pressurized water.
- Impervious to atmospheric and marine corrosion.
Standards
- NEMA Type 4, 4X, 12 and 13
- IP66
- UL94 HB Flammability Rating
Construction
- Molded in ABS plastic.
- Separate mounting channels & lid channels.
- Recessed polyurethane gasket with tongue and groove construction.
- Interlocking flange on lid and bottom sections.
- Captive stainless steel lid screws are provided.
- Cover screws fasten into pre-threaded holes.
Finish
- Light grey RAL 7035
- Separate screw channels outside of the gasket seal (lid screws & enclosure mounting screws).
- There are many mounting posts for self tapping screws in both the enclosure & the lid. Can also be used for mounting P.C. boards or plates.
- Thermoplastic forpene gasket.
- Enclosure mounts through channel and bottom holes, concealed when lid is attached.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: mm. Switch units to: inch
Part No. Length Width Height R220-060-000 66 51 35 R220-080-000 83 81 60 R220-082-000 121 81 60 R220-084-000 161 81 60 R220-102-000 151 101 60 R220-104-000 201 101 60 R220-120-000 123 121 80 R220-122-000 201 121 80 R220-160-000 161 161 80 R220-162-000 241 161 80 SKU: R220-060-000 -
Discontinued Products
Water-Tight Polyester R130-131-132 Series – (R132-080-000) (DISCONTINUED)
Key Information:
Application:
- Designed for use as instrument enclosures, electrical junction boxes or terminal wiring enclosures.
- Provide outstanding protection against dust, oil and pressurized water.
- Impervious to atmospheric and marine corrosion.
Construction:
- Two piece molded fiberglass reinforced polyester construction.
- Captive polyfibre cover screws are provided with a standard slot head.
- Cover screws fasten into pre-threaded holes.
- The threaded cover screw holes also provide single channel access to rear mounting positions.
- Recessed neoprene gasket with tongue and groove construction is oil and petroleum resistant.
- Threaded stainless steel inserts provide for internal mounting.
Finish:
- Light beige RAL 7032, Pantone 413
- Spring loaded stainless steel hinge pins are standard, allowing for quick lid removal . (R130 & R131 Series only)
Standards:
- NEMA Type 1, 2, 3, 3R, 4, 4X, 5, 12 and 13
- IEC 529, IP66
- V0 Flammability Rating
- CSA certified, Type 4, for use with industrial control equipment
Photo Features
- Captive screws made of strong polyamide, corrosion free.
- Oil resistant CR gasket.
- Easily removable stainless steel hinge pin.
- Four stainless steel M6 inserts in bottom of enclosure (screws not included).
- Single channel lid and enclosure fastening access – for maximum internal space (ie, lid mounting hole doubles as the access to the bottom hole to mount enclosure to the wall). Outside the gasket seal and includes stainless steel inserts.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
With Integrated Hinges
Units shown: mm. Switch units to: inch
Part No. Width Length Depth R130-120-000 120 140 100 R130-122-000 120 200 100 R130-124-000 120 260 100 R130-160-000 160 180 100 R130-162-000 160 260 100 R130-164-000 160 340 100 R130-200-000 200 220 120 R130-202-000 200 320 120 With Integrated Hinges & Acrylic Window in Lid
Units shown: mm. Switch units to: inch
Part No. Width Length Height R131-120-000 120 140 100 R131-122-000 120 200 100 R131-124-000 120 260 100 R131-160-000 160 180 100 R131-162-000 160 260 100 R131-164-000 160 340 100 R131-200-000 200 220 120 R131-202-000 200 320 120 With Lid Screws Only (No Hinge)
Units shown: mm. Switch units to: inch
Part No. Width Length Height R132-080-000 82 82 60 R132-082-000 82 122 60 R132-084-000 82 162 60 R132-100-000 102 102 81 R132-102-000 102 152 81 R132-104-000 102 202 81 R132-120-000 124 124 100 R132-122-000 124 184 100 R132-124-000 124 244 100 R132-160-000 164 164 100 R132-162-000 164 244 100 R132-164-000 164 324 100 R132-400-000 404 404 160 SKU: R132-080-000 -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB181110) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB181110 -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB181170VL) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB181170VL -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB181170) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB181170 -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB181160) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB181160 -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB158080) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB158080 -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB158055VL) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB158055VL -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB158055) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB158055 -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB126565) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB126565 -
Discontinued Products
Two Tone Fixed Panel Enclosures MB Series – (MB126540VL) (DISCONTINUED)
Key Features:
- Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
- Front and rear panels are integral part of bottom unit.
- Molded in polystyrene plastic.
- Designed to meet IP54.
- Assembled with four M4 x 0.7” (14 mm) slotted machine screws (included) threaded into integral brass bushings. Perfect for applications with repetitive assembly and disassembly are required. Screws are hidden in a recess in the base (see above – bottom view).
- Includes four M3 X 0.276″ (7mm) self tapping screws for internal standoffs.
- Lid is a smooth light gray (RAL 7035) and the bottom is a smooth dark gray (RAL 7012).
Gallery
SKU: MB126540VL