Discontinued Products
Showing 9793–9816 of 10717 results
-
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487EK) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487EK -
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487DK) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487DK -
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487CK) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487CK -
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487CRE) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487CRE -
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487CRC) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487CRC -
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487BS) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487BS -
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487BH) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487BH -
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487BK) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487BK -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485FS9) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485FS9 -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485ES9) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485ES9 -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485DS9) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485DS9 -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485CS9) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485CS9 -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485FSM) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485FSM -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485ESM) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485ESM -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485DSM) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485DSM -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485CSM) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485CSM -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485DH) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485DH -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485CH) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485CH -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485DL2) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485DL2 -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485CL2) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485CL2 -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485DL1) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485DL1 -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485CL1) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485CL1 -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485DK) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485DK -
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485CK) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
- Typical Straight Section
- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485CK