American Tech Supply Full Catalog
Showing 73777–73800 of 75476 results
-
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1550WMS100BK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1550WMS100BK -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1550WMS100) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1550WMS100 -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1550MS100BK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1550MS100BK -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (SCDRIVET10-2) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: SCDRIVET10-2 -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1590WMS50TBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1590WMS50TBK -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1590WMS50T) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1590WMS50T -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1590MS50TBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1590MS50TBK -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1590MS50T) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1590MS50T -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1590WMS100BK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1590WMS100BK -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1590WMS100) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1590WMS100 -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1590MS50BK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1590MS50BK -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1550MS100) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1550MS100 -
Discontinued Products
Diecast Aluminum Enclosures 1590 Series – (1590MS100) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough – yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance appearance.
- Includes screws threaded into factory-tapped holes. Screw type and quantity vary. See details below or in drawings.
- Standard versions are designed to meet IP54.
- Water-tight versions are designed to meet IP65 and include a gasket. Gasket is supplied loose inside the enclosure (not pre-installed).
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Photo Features
Hardware
NOTE: 1590 series enclosures feature factory-tapped assembly screw holes that accept machine screws, which are included with the enclosures. Most sizes require four (4) screws. 1590BX, 1590BX2, 1590D, 1590DD, 1590DE, 1590E, 1590EE & 1590R1 require six (6). 1590F requires eight (8). See drawings and/or photos for details.Replacement Hardware
Tamper-proof Hardware Upgrade (Torx w/ Pin)
See “Hardware” table below for compatibility.
Gaskets
NOTE: Gaskets are included with watertight 1590 enclosures. They can also be purchased as a kit if you’d like to upgrade an IP54 enclosure to IP65.
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid.
- Gasket as a temperature rating of -40C to +150C
- Designed to meet IP65 with properly installed gasket and lid screws torqued to 25-30 cN.m (36-43 ozf.in).
- Refer to part number table below for correct gasket.
Notes
- Lid height is 0.16″ (4 mm)
- Don’t forget to order our watertight screws (stainless steel with o-ring) when converting a standard enclosure to a water-tight box.
Other 1590-Series Enclosures
- Nine of our popular “stomp box” sizes are also available in a variety of colors. See the 1590-STOMP series for details.
- Three of our popular sizes are also available in diecast zinc (series 1590K4). The zinc alloy is heavy weight, high impact, and easy to machine & plate.
- The 1590-RIBBED series features internal vertical ribs on the side walls.
SKU: 1590MS100 -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (SC1550Z220-30) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (SC1550Z220-30) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: SC1550Z220-30 -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (1550Z124GASKET) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (1550Z124GASKET) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: 1550Z124GASKET -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (1550Z120GASKET) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (1550Z120GASKET) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: 1550Z120GASKET -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (1550Z116GASKET) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (1550Z116GASKET) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: 1550Z116GASKET -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (1550Z139GASKET) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (1550Z139GASKET) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: 1550Z139GASKET -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (1550Z109GASKET) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (1550Z109GASKET) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: 1550Z109GASKET -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (1550Z115GASKET) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (1550Z115GASKET) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: 1550Z115GASKET -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (1550Z107GASKET) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (1550Z107GASKET) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: 1550Z107GASKET -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (SCGM4-50) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (SCGM4-50) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: SCGM4-50 -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (SC1550Z107-50) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (SC1550Z107-50) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: SC1550Z107-50 -
Discontinued Products
Watertight Diecast Aluminum Enclosures 1550Z Series – (1550Z137GASKET) (DISCONTINUED)
Discontinued ProductsWatertight Diecast Aluminum Enclosures 1550Z Series – (1550Z137GASKET) (DISCONTINUED)
Key Features:
- Very economical – thick wall – diecast aluminum – watertight electronic instrument enclosure.
- Rugged, diecast aluminum alloy (tough – yet easy to machine),
- Two piece “tongue & groove” construction for protection against access of dust and water.
- Ideal for repetitive opening and closing.
- Easy to wall mount using “through box – blind hole” construction (on all sizes except: 1550Z102, 1550Z115 & 1550Z120). Access to blind holes is outside of gasket ring for superior protection (see photo features below).
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Textured black version is coated with tough polyester powder for a lasting finish, even after machining. Finish is applied to the entire enclosure (inside & out).
- Lid secured with either two, four or six (count varies with size) stainless steel, Philips head, counter sunk, machine screws – into factory tapped holes.
- Lid screws are outside the gasket protection area to eliminate the need for “O” rings on the screws.
- On six sizes (the 1550Z107, 1550Z108, 1550Z116, 1550Z117, 1550Z137 & 1550Z139) lid screws are self captivating. The lid holes are slightly undersized & threaded with the first installation of the self tapping – lid screws (see photos)). Enclosure holes are pre-tapped.
- Designed to meet IP66 (NEMA 1, 4, 4X, 12 & 13 ratings. Gasket is pre-formed, one-piece silicone rubber and installs easily into lid groove.
- Gasket has a temperature rating of -40C to +150C
- North American Mark of Safety – cUL & UL listed. Certified to NEMA 4X standards – File #E71073
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
Accessories
SKU: 1550Z137GASKET