American Tech Supply Full Catalog
Showing 73849–73872 of 75476 results
-
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WJBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WJBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WJ) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WJ -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550JBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550JBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550NSGASKET) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550NSGASKET -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550NEGASKET) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550NEGASKET -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WHBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WHBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WH) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WH -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550HBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550HBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550GSGASKET) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550GSGASKET -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550GEGASKET) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550GEGASKET -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WGBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WGBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WG) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WG -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550GBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550GBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WFBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WFBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WF) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WF -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550FBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550FBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550ESGASKET) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550ESGASKET -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550EEGASKET) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550EEGASKET -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WEBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WEBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WE) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WE -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550EBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550EBK -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550LSGASKET) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550LSGASKET -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550LEGASKET) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550LEGASKET -
Discontinued Products
Diecast Aluminum Enclosures 1550 Series – (1550WLBK) (DISCONTINUED)
Features
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Available in natural vibra finish OR in light textured, black powder paint.
- Unpainted version is vibra finished for a smooth surface with no sharp edges.
- Painted version is painted with tough satin black polyester powder paint for a lasting finish, even after machining. Black screws are included to enhance the assembled appearance.
- Lap joint construction protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. The enclosure does not provide shielding when water-tight gaskets are installed.
- M3.5 x 0.6 x 12 mm long stainless steel, Philips head, machine screws secure lid into factory tapped holes.
- Designed to meet IP 54 without a gasket or IP66 with a gasket. IP67 upgraded gaskets are available.
- All sizes except 1550Z101** carry an impact rating of IK08 per IEC62262
- No internal ribs for easy installation of connectors without interference or additional milling.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Add 0.16″ (4 mm) to enclosure depth for lid
Replacement Hardware
- Replacement screws for the unpainted series – 1550MS100 – Package of 100
- Replacement screws for the black series – 1550MS100BK – Package of 100
Upgrade To Tamper-Resistant (Torx With Pin) Hardware
- Tamper-resistant screws for the unpainted series – 1550MS50T– Package of 50
- Tamper-resistant screws for the black series –1550MS50TBK – Package of 50
- Driver bit for tamper-proof screws – SCDRIVET15-2
Accessory Gasket Kits
- IP66
- Each kit includes two pre-formed economical EVA foam gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later
- Gasket is applied to the lid (see photo example below).
- Designed to meet IP 66 (with properly installed gasket and lid screws torqued at 55 cN.m).
- EVA Foam gasket rated up to 65 degrees C.
- IP67 Upgrade
- Each kit includes two pre-formed silicone gaskets.
- Gaskets include adhesive backing for easy installation.
- Allows enclosure to be machined and/or painted first and gasketed later.
- Gasket is applied to the lid (see photo example below).
- Tested to meet IP 67 (with properly installed gasket and lid screws torqued at 55 cN.m).
- Silicone gasket has a temperature rating of -40C to +150C
Photo Features (click to enlarge):
SKU: 1550WLBK