Shop By Brand
American Tech Supply Full Catalog
Showing 97–120 of 115351 results
-
Discontinued Products
Type 12 Lay-In Wireway 1485 Series – (1485FTN) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
- Flanges are open at the top to allow cables to lay in when doors open.
- 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during
installation. - Butt hinged cover is secured with easily operated quick release clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
- Sealing plate is supplied.
- Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.
Finish
- Sections and components are finished in ANSI 61 gray powder coating.
Notes
- When joining a wireway section or fitting to an enclosure be sure to order a box connector.
- When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
- When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
- Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.
Accessories
Typical Straight Section- Flat Sealing Plate
- Angle Sealing Plate
- Barrier Kit
- Swivel Nipple
- Flexible Fitting
- Adjustable Fitting
- Cross Fitting
- Cut-Off Fitting (Lay-In)
- Cut-Off Fitting (Non Lay-In)
- Nipple
- 45 degree Elbow Top Opening
- 45 degree Elbow Inside Opening
- 45 degree Elbow Outside Opening
- 90 degree Elbow Top Opening
- 90 degree Elbow Inside Opening
- 90 degree Elbow Outside Opening
- Tee Fitting Top Opening
- Tee Fitting Outside and Top Opening
- Reducers
- Box Connector
- 12″ Transposition Sections Clockwise & Counter-Clockwise
- Drop Hanger
- Bracket Hanger
- Cover Plate
- Junction Box
SKU: 1485FTN -
Discontinued Products
Type 12 Consolets 1488 Series – (1488JQ11) (DISCONTINUED)
Application
- Designed for use as electric, hydraulic or pneumatic control and instrument enclosures.
- Ideal for flat or surface mounting/pedestal to provide the necessary 30° or 60° control slope.
- Provides protection from dirt, dust, oil and water.
Standards
- UL 508A Type 12, 13
- CSA Type 12, 13
- Complies with
- NEMA Type 12, 13
- IEC 60529, IP54
Construction
- Formed 14 gauge steel.
- Smooth, continuously welded seams.
- Construction provides either 30° or 60° slope on front cover depending on mounting position.
- Continuously hinged cover may be removed by pulling the hinge pin.
- Captive cover screws thread into sealed wells.
- Oil resistant gasket and adhesive.
- A bonding stud is provided on the door and a ground stud is provided on the enclosure.
Finish
- Cover and enclosure are phosphatized and finished in ANSI 61 gray powder coating.
Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Enclosure Part No. Cover H H1 H2 W D 1488EE7 8.00 2.50 7.16 8.00 7.44 1488EH7 8.00 2.50 7.16 12.00 7.44 1488EJ7 8.00 2.50 7.16 16.00 7.44 1488EL7 8.00 2.50 7.16 20.00 7.44 1488HH9 12.00 2.50 9.16 12.00 10.90 1488HJ9 12.00 2.50 9.16 16.00 10.90 1488HL9 12.00 2.50 9.16 20.00 10.90 1488HN9 12.00 2.50 9.16 24.00 10.90 1488JJ11 16.00 2.50 11.16 16.00 14.37 1488JL11 16.00 2.50 11.16 20.00 14.37 1488JN11 16.00 2.50 11.16 24.00 14.37 1488JQ11 16.00 2.50 11.16 30.00 14.37 1488JS11 16.00 2.50 11.16 36.00 14.37 1488LL13 20.00 2.50 13.16 20.00 17.83 1488LN13 20.00 2.50 13.16 24.00 17.83 1488LQ13 20.00 2.50 13.16 30.00 17.83 SKU: 1488JQ11 -
Discontinued Products
(Discontinued) Outdoor FilterFans 3RFF Series – (PF43000T3RBK230)
Features
- Designed for outdoor weather where resistance against falling rain, ice formation, and UV degradation is important to ensure operation of apparatus inside enclosure.
- Maintains a UL Tested NEMA Type 3R seal against enclosure without need of a rainhood
- Patented “Click & Fit” design provides a hardware free installation!
- Plastic made from strong, heat resistant (ABS-FR), UL 94 VO fire approved material
- Fluted filter-mat provides longer service life, holding more dust before impeding airflow extending the mean time between maintenance for outdoor enclosure; especially critical for those located in remote areas.
- Offered in Light Gray (RAL 7035) and Black (RAL 9011)
Accessories
SKU: PF43000T3RBK230 -
Discontinued Products
(Discontinued) Outdoor FilterFans 3RFF Series – (PF43000T3RLG230)
Features
- Designed for outdoor weather where resistance against falling rain, ice formation, and UV degradation is important to ensure operation of apparatus inside enclosure.
- Maintains a UL Tested NEMA Type 3R seal against enclosure without need of a rainhood
- Patented “Click & Fit” design provides a hardware free installation!
- Plastic made from strong, heat resistant (ABS-FR), UL 94 VO fire approved material
- Fluted filter-mat provides longer service life, holding more dust before impeding airflow extending the mean time between maintenance for outdoor enclosure; especially critical for those located in remote areas.
- Offered in Light Gray (RAL 7035) and Black (RAL 9011)
Accessories
SKU: PF43000T3RLG230 -
Discontinued Products
Type 4X Polyester Junction Box w/ Window PJ Series – (PJ18168HW) (DISCONTINUED)
Discontinued ProductsType 4X Polyester Junction Box w/ Window PJ Series – (PJ18168HW) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
- Ideal in applications with high temperatures or highly corrosive environments.
Standards
- UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
- CSA Type 1, 2, 3, 4, 4X, 12 and 13
- Complies with
- NEMA Type 1, 2, 3, 4, 4X, 12, & 13
- IEC 60529, IP66
Construction
- Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
- Enhanced UV inhibitors protect against outdoor weathering.
- Standard JIC sizes under 18″x16″.
- Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
- Stainless steel draw type “snap latch” door fasteners.
- Door fasteners include a provision for padlocking.
- Enclosures are available with bonded polycarbonate viewing windows.
- Door is supported with a continuous stainless steel hinge.
- Captive oil resistant gasket provides a positive seal.
- Threaded brass inserts are provided for mounting feet to the rear of the enclosure.
- Stainless steel mounting brackets and hardware are provided for mounting to the rear of the enclosure.
- Operating temperatures between 130°C and -40°C (266°F to -40°F).
- Impact index of 6.78J (5 ft/lb).
- For corrosion resistance information, please refer to table in the Technical Information section.
Finish
- Fiberglass polyester material has a gray finish.
- Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.
Accessories
- Additional Inner Panels
- Terminal Kit Assemblies
- Pole Mounting Kit
- PJ/PJU/PCJ Replacement Hardware Kits
- PJ Stainless Replacement Mounting Feet
- Climate Control
- General Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Lift-Off Hinged Snap Latch Twist Latch Enclosure Optional Inner Panel Part No. Part No. Part No. Part No. H W D H W Part No. PJ664W PJ664HW PJ664LW PJ664TW 6.10 6.10 4.18 4.88 4.88 14R0505 PJ864W PJ864HW PJ864LW PJ864TW 8.00 6.12 4.13 6.75 4.88 14R0705 PJ1084W PJ1084HW PJ1084LW PJ1084TW 10.13 8.26 4.13 8.75 6.88 14R0907 PJ1086W PJ1086HW PJ1086LW PJ1086TW 10.13 8.26 6.13 8.75 6.88 14R0907 PJ12106W PJ12106HW PJ12106LW PJ12106TW 12.13 10.26 6.13 10.75 8.88 14R1109 PJ12124W PJ12124HW PJ12124LW PJ12124TW 12.13 12.13 4.13 10.75 10.88 14R1111 PJ12126W PJ12126HW PJ12126LW PJ12126TW 12.13 12.13 6.13 10.75 10.88 14R1111 PJ14126W PJ14126HW PJ14126LW PJ14126TW 14.13 12.26 6.13 12.75 10.88 14R1311 PJ16148W PJ16148HW PJ16148LW PJ16148TW 16.27 14.40 8.13 14.75 12.88 14R1513 PJ18168W PJ18168HW PJ18168LW PJ18168TW 18.40 16.40 8.13 16.88 14.88 P1868 PJ20168W PJ20168HW PJ20168LW PJ20168TW 20.00 16.00 8.13 18.44 14.44 P2068 SKU: PJ18168HW -
Discontinued Products
Type 4X Polyester Junction Box w/ Window PJ Series – (PJ18168W) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
- Ideal in applications with high temperatures or highly corrosive environments.
Standards
- UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
- CSA Type 1, 2, 3, 4, 4X, 12 and 13
- Complies with
- NEMA Type 1, 2, 3, 4, 4X, 12, & 13
- IEC 60529, IP66
Construction
- Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
- Enhanced UV inhibitors protect against outdoor weathering.
- Standard JIC sizes under 18″x16″.
- Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
- Stainless steel draw type “snap latch” door fasteners.
- Door fasteners include a provision for padlocking.
- Enclosures are available with bonded polycarbonate viewing windows.
- Door is supported with a continuous stainless steel hinge.
- Captive oil resistant gasket provides a positive seal.
- Threaded brass inserts are provided for mounting feet to the rear of the enclosure.
- Stainless steel mounting brackets and hardware are provided for mounting to the rear of the enclosure.
- Operating temperatures between 130°C and -40°C (266°F to -40°F).
- Impact index of 6.78J (5 ft/lb).
- For corrosion resistance information, please refer to table in the Technical Information section.
Finish
- Fiberglass polyester material has a gray finish.
- Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.
Accessories
- Additional Inner Panels
- Terminal Kit Assemblies
- Pole Mounting Kit
- PJ/PJU/PCJ Replacement Hardware Kits
- PJ Stainless Replacement Mounting Feet
- Climate Control
- General Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Lift-Off Hinged Snap Latch Twist Latch Enclosure Optional Inner Panel Part No. Part No. Part No. Part No. H W D H W Part No. PJ664W PJ664HW PJ664LW PJ664TW 6.10 6.10 4.18 4.88 4.88 14R0505 PJ864W PJ864HW PJ864LW PJ864TW 8.00 6.12 4.13 6.75 4.88 14R0705 PJ1084W PJ1084HW PJ1084LW PJ1084TW 10.13 8.26 4.13 8.75 6.88 14R0907 PJ1086W PJ1086HW PJ1086LW PJ1086TW 10.13 8.26 6.13 8.75 6.88 14R0907 PJ12106W PJ12106HW PJ12106LW PJ12106TW 12.13 10.26 6.13 10.75 8.88 14R1109 PJ12124W PJ12124HW PJ12124LW PJ12124TW 12.13 12.13 4.13 10.75 10.88 14R1111 PJ12126W PJ12126HW PJ12126LW PJ12126TW 12.13 12.13 6.13 10.75 10.88 14R1111 PJ14126W PJ14126HW PJ14126LW PJ14126TW 14.13 12.26 6.13 12.75 10.88 14R1311 PJ16148W PJ16148HW PJ16148LW PJ16148TW 16.27 14.40 8.13 14.75 12.88 14R1513 PJ18168W PJ18168HW PJ18168LW PJ18168TW 18.40 16.40 8.13 16.88 14.88 P1868 PJ20168W PJ20168HW PJ20168LW PJ20168TW 20.00 16.00 8.13 18.44 14.44 P2068 SKU: PJ18168W -
Discontinued Products
Type 4X Polyester Junction Box w/ Window PJU Series – (PJU16148LWF) (DISCONTINUED)
Discontinued ProductsType 4X Polyester Junction Box w/ Window PJU Series – (PJU16148LWF) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
- Ideal in applications with high temperatures or highly corrosive environments.
Standards
- UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
- CSA Type 1, 2, 3, 4, 4X, 12 and 13
- Complies with
- NEMA Type 1, 2, 3, 4, 4X, 12 and 13
- IEC 60529, IP66
Construction
- Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
- Enhanced UV inhibitors protect against outdoor weathering.
- Standard JIC sizes under 18″x16″.
- Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
- Various latching options.
- Enclosures are available with bonded polycarbonate viewing windows.
- Door is supported with a continuous stainless steel hinge pin.
- Captive oil resistant gasket provides a positive seal.
- Threaded brass inserts are provided for mounting feet to the rear of the enclosure.
- Operating temperatures between 130°C and -40°C (266°F to -40°F).
- Impact index of 6.78J (5 ft/lb).
- For corrosion resistance information, please refer to table in the Technical Information section.
Finish
- Fiberglass polyester material has a light gray finish.
- Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.
Accessories
SKU: PJU16148LWF -
Discontinued Products
(Discontinued) 125-1300 W Fan Heater with Thermostat FLH Series – (FLHTF400A230)
Discontinued Products(Discontinued) 125-1300 W Fan Heater with Thermostat FLH Series – (FLHTF400A230)
Features
- Designed to prevent condensation or maintain minimum temperature in enclosures.
- Built in Thermostat. (-18 C to +38 C) (0 F to +100 F)
- Fan Auto/On switch with pilot light for Heat On indication
- High temperature safety protection
- Aluminum alloy outer casing
- Connection via terminal block.
- 1300W models are cURus approved only.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Overall Dimensions Part No. Watts Voltage Hz CFM Height x Width x Depth FLHTF125A115 125 W 120 V 60 20 5.5″ x 4.0″ x 5.3″ FLHTF125A230 105/125 W 220/240 V 50/60 20 5.5″ x 4.0″ x 5.3″ FLHTF200A115 200 W 120 V 60 20 5.5″ x 4.0″ x 5.3″ FLHTF200A230 165/200 W 220/240 V 50/60 20 5.5″ x 4.0″ x 5.3″ FLHTF400A115 400 W 120 V 60 20 7.5″ x 4.0″ x 5.3″ FLHTF400A230 335/400 W 220/240 V 50/60 20 7.5″ x 4.0″ x 5.3″ FLHTF800A115 800 W 120 V 60 20 7.5″ x 4.0″ x 5.3″ FLHTF800A230 670/800 W 220/240 V 50/60 20 7.5″ x 4.0″ x 5.3″ FLHTF1300A115 1300 W 120 V 60 50 7.5″ x 5.6″ x 6.9″ FLHTF1300A230 1080/1300 W 220/240 V 50/60 50 7.5″ x 5.6″ x 6.9″ SKU: FLHTF400A230 -
Discontinued Products
(Discontinued) 125-1300 W Fan Heater with Thermostat FLH Series – (FLHTF400A115)
Discontinued Products(Discontinued) 125-1300 W Fan Heater with Thermostat FLH Series – (FLHTF400A115)
Features
- Designed to prevent condensation or maintain minimum temperature in enclosures.
- Built in Thermostat. (-18 C to +38 C) (0 F to +100 F)
- Fan Auto/On switch with pilot light for Heat On indication
- High temperature safety protection
- Aluminum alloy outer casing
- Connection via terminal block.
- 1300W models are cURus approved only.
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Overall Dimensions Part No. Watts Voltage Hz CFM Height x Width x Depth FLHTF125A115 125 W 120 V 60 20 5.5″ x 4.0″ x 5.3″ FLHTF125A230 105/125 W 220/240 V 50/60 20 5.5″ x 4.0″ x 5.3″ FLHTF200A115 200 W 120 V 60 20 5.5″ x 4.0″ x 5.3″ FLHTF200A230 165/200 W 220/240 V 50/60 20 5.5″ x 4.0″ x 5.3″ FLHTF400A115 400 W 120 V 60 20 7.5″ x 4.0″ x 5.3″ FLHTF400A230 335/400 W 220/240 V 50/60 20 7.5″ x 4.0″ x 5.3″ FLHTF800A115 800 W 120 V 60 20 7.5″ x 4.0″ x 5.3″ FLHTF800A230 670/800 W 220/240 V 50/60 20 7.5″ x 4.0″ x 5.3″ FLHTF1300A115 1300 W 120 V 60 50 7.5″ x 5.6″ x 6.9″ FLHTF1300A230 1080/1300 W 220/240 V 50/60 50 7.5″ x 5.6″ x 6.9″ SKU: FLHTF400A115 -
Discontinued Products
Type 4X Polyester Junction Box w/ Window PJ Series – (PJ16148TW) (DISCONTINUED)
Discontinued ProductsType 4X Polyester Junction Box w/ Window PJ Series – (PJ16148TW) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
- Ideal in applications with high temperatures or highly corrosive environments.
Standards
- UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
- CSA Type 1, 2, 3, 4, 4X, 12 and 13
- Complies with
- NEMA Type 1, 2, 3, 4, 4X, 12, & 13
- IEC 60529, IP66
Construction
- Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
- Enhanced UV inhibitors protect against outdoor weathering.
- Standard JIC sizes under 18″x16″.
- Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
- Stainless steel draw type “snap latch” door fasteners.
- Door fasteners include a provision for padlocking.
- Enclosures are available with bonded polycarbonate viewing windows.
- Door is supported with a continuous stainless steel hinge.
- Captive oil resistant gasket provides a positive seal.
- Threaded brass inserts are provided for mounting feet to the rear of the enclosure.
- Stainless steel mounting brackets and hardware are provided for mounting to the rear of the enclosure.
- Operating temperatures between 130°C and -40°C (266°F to -40°F).
- Impact index of 6.78J (5 ft/lb).
- For corrosion resistance information, please refer to table in the Technical Information section.
Finish
- Fiberglass polyester material has a gray finish.
- Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.
Accessories
- Additional Inner Panels
- Terminal Kit Assemblies
- Pole Mounting Kit
- PJ/PJU/PCJ Replacement Hardware Kits
- PJ Stainless Replacement Mounting Feet
- Climate Control
- General Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Lift-Off Hinged Snap Latch Twist Latch Enclosure Optional Inner Panel Part No. Part No. Part No. Part No. H W D H W Part No. PJ664W PJ664HW PJ664LW PJ664TW 6.10 6.10 4.18 4.88 4.88 14R0505 PJ864W PJ864HW PJ864LW PJ864TW 8.00 6.12 4.13 6.75 4.88 14R0705 PJ1084W PJ1084HW PJ1084LW PJ1084TW 10.13 8.26 4.13 8.75 6.88 14R0907 PJ1086W PJ1086HW PJ1086LW PJ1086TW 10.13 8.26 6.13 8.75 6.88 14R0907 PJ12106W PJ12106HW PJ12106LW PJ12106TW 12.13 10.26 6.13 10.75 8.88 14R1109 PJ12124W PJ12124HW PJ12124LW PJ12124TW 12.13 12.13 4.13 10.75 10.88 14R1111 PJ12126W PJ12126HW PJ12126LW PJ12126TW 12.13 12.13 6.13 10.75 10.88 14R1111 PJ14126W PJ14126HW PJ14126LW PJ14126TW 14.13 12.26 6.13 12.75 10.88 14R1311 PJ16148W PJ16148HW PJ16148LW PJ16148TW 16.27 14.40 8.13 14.75 12.88 14R1513 PJ18168W PJ18168HW PJ18168LW PJ18168TW 18.40 16.40 8.13 16.88 14.88 P1868 PJ20168W PJ20168HW PJ20168LW PJ20168TW 20.00 16.00 8.13 18.44 14.44 P2068 SKU: PJ16148TW -
Discontinued Products
Type 4X Polyester Junction Box w/ Window PJ Series – (PJ16148LW) (DISCONTINUED)
Discontinued ProductsType 4X Polyester Junction Box w/ Window PJ Series – (PJ16148LW) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
- Ideal in applications with high temperatures or highly corrosive environments.
Standards
- UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
- CSA Type 1, 2, 3, 4, 4X, 12 and 13
- Complies with
- NEMA Type 1, 2, 3, 4, 4X, 12, & 13
- IEC 60529, IP66
Construction
- Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
- Enhanced UV inhibitors protect against outdoor weathering.
- Standard JIC sizes under 18″x16″.
- Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
- Stainless steel draw type “snap latch” door fasteners.
- Door fasteners include a provision for padlocking.
- Enclosures are available with bonded polycarbonate viewing windows.
- Door is supported with a continuous stainless steel hinge.
- Captive oil resistant gasket provides a positive seal.
- Threaded brass inserts are provided for mounting feet to the rear of the enclosure.
- Stainless steel mounting brackets and hardware are provided for mounting to the rear of the enclosure.
- Operating temperatures between 130°C and -40°C (266°F to -40°F).
- Impact index of 6.78J (5 ft/lb).
- For corrosion resistance information, please refer to table in the Technical Information section.
Finish
- Fiberglass polyester material has a gray finish.
- Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.
Accessories
- Additional Inner Panels
- Terminal Kit Assemblies
- Pole Mounting Kit
- PJ/PJU/PCJ Replacement Hardware Kits
- PJ Stainless Replacement Mounting Feet
- Climate Control
- General Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Lift-Off Hinged Snap Latch Twist Latch Enclosure Optional Inner Panel Part No. Part No. Part No. Part No. H W D H W Part No. PJ664W PJ664HW PJ664LW PJ664TW 6.10 6.10 4.18 4.88 4.88 14R0505 PJ864W PJ864HW PJ864LW PJ864TW 8.00 6.12 4.13 6.75 4.88 14R0705 PJ1084W PJ1084HW PJ1084LW PJ1084TW 10.13 8.26 4.13 8.75 6.88 14R0907 PJ1086W PJ1086HW PJ1086LW PJ1086TW 10.13 8.26 6.13 8.75 6.88 14R0907 PJ12106W PJ12106HW PJ12106LW PJ12106TW 12.13 10.26 6.13 10.75 8.88 14R1109 PJ12124W PJ12124HW PJ12124LW PJ12124TW 12.13 12.13 4.13 10.75 10.88 14R1111 PJ12126W PJ12126HW PJ12126LW PJ12126TW 12.13 12.13 6.13 10.75 10.88 14R1111 PJ14126W PJ14126HW PJ14126LW PJ14126TW 14.13 12.26 6.13 12.75 10.88 14R1311 PJ16148W PJ16148HW PJ16148LW PJ16148TW 16.27 14.40 8.13 14.75 12.88 14R1513 PJ18168W PJ18168HW PJ18168LW PJ18168TW 18.40 16.40 8.13 16.88 14.88 P1868 PJ20168W PJ20168HW PJ20168LW PJ20168TW 20.00 16.00 8.13 18.44 14.44 P2068 SKU: PJ16148LW -
Discontinued Products
Potted High Voltage (Plate) (DISCONTINUED) & Filament – 40 VA to 243 VA 300P Series – (370XP) (DISCONTINUED)
Discontinued ProductsPotted High Voltage (Plate) (DISCONTINUED) & Filament – 40 VA to 243 VA 300P Series – (370XP) (DISCONTINUED)
Features
- A perfect match to our 1650P potted output transformers.
- Enclosed in a drawn steel case, the transformer is completely potted in epoxy.
- Mounting hardware included.
- Primary: Universal – 100, 110, 120, 200, 220, 240 VAC 50/60 Hz.
- Bias Tap: 50 VAC tap from high voltage secondary C.T.
- Highpot tested: 2,000 VAC
- Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary – greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
- Windings: Concentric wound for low stray field and low noise
- Finish: Black powder paint to match our 1650P series of potted output transformers
- Units can be run full wave bridge or full wave C.T.
- c UL us recognized (E207860)
Gallery
SKU: 370XP -
Discontinued Products
Type 4X Polyester Junction Box w/ Window PJU Series – (PJU14126LWF) (DISCONTINUED)
Discontinued ProductsType 4X Polyester Junction Box w/ Window PJU Series – (PJU14126LWF) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
- Ideal in applications with high temperatures or highly corrosive environments.
Standards
- UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
- CSA Type 1, 2, 3, 4, 4X, 12 and 13
- Complies with
- NEMA Type 1, 2, 3, 4, 4X, 12 and 13
- IEC 60529, IP66
Construction
- Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
- Enhanced UV inhibitors protect against outdoor weathering.
- Standard JIC sizes under 18″x16″.
- Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
- Various latching options.
- Enclosures are available with bonded polycarbonate viewing windows.
- Door is supported with a continuous stainless steel hinge pin.
- Captive oil resistant gasket provides a positive seal.
- Threaded brass inserts are provided for mounting feet to the rear of the enclosure.
- Operating temperatures between 130°C and -40°C (266°F to -40°F).
- Impact index of 6.78J (5 ft/lb).
- For corrosion resistance information, please refer to table in the Technical Information section.
Finish
- Fiberglass polyester material has a light gray finish.
- Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.
Accessories
SKU: PJU14126LWF -
Discontinued Products
Type 3R Painted Galvanized Steel Enclosure C3R HCLO Series – (C3R30248HCLO) (DISCONTINUED)
Discontinued ProductsType 3R Painted Galvanized Steel Enclosure C3R HCLO Series – (C3R30248HCLO) (DISCONTINUED)
Application
- Designed for use as a wiring/junction box.
- Provides protection against rain, sleet, snow and dripping water.
Standards
- UL-50 Type 3R
- CSA Type 3R
- Complies with
- NEMA Type 3R
- IEC 60529, IP24
Construction
- Formed and spot welded from 16 gauge galvanized steel (14 gauge when 24″ wide)
- Extended height door and seam-free sides, front and back.
- Galvanized steel lift-off hinges with stainless steel pins.
- Cover fastened securely with zinc plated draw pull catches.
- Provisions for padlocking on zinc-plated draw pull catch.
- Embossed mounting holes on back.
- Foam gasket seal around door opening.
Finish
- Enclosure and cover are finished in ANSI 61 gray powder coating.
Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Enclosure Optional Inner Panel Optional Panel Optional Mount Part No. H W D Part No. H W Mounting Kit Foot Kit C3R864HCLO 8.00 6.00 4.00 14R0505 4.88 4.88 C3RHCLOPK1 C3RHCLOMFK1 C3R886HCLO 8.00 8.00 6.00 14R0705 6.75 4.88 C3RHCLOPK1 C3RHCLOMFK1 C3R1086HCLO 10.00 8.00 6.00 14R0707 6.75 6.88 C3RHCLOPK1 C3RHCLOMFK1 C3R12106HCLO 12.00 10.00 6.00 14R0909 8.75 8.88 C3RHCLOPK1 C3RHCLOMFK1 C3R12126HCLO 12.00 12.00 6.00 14R1109 10.75 8.88 C3RHCLOPK1 C3RHCLOMFK1 C3R16126HCLO 16.00 12.00 6.00 14R1311 12.75 10.88 C3RHCLOPK1 C3RHCLOMFK1 C3R16166HCLO 16.00 16.00 6.00 18P1313 13.00 13.00 C3RHCLOPK2 C3RHCLOMFK2 C3R20166HCLO 20.00 16.00 6.00 18P1713 17.00 13.00 C3RHCLOPK2 C3RHCLOMFK2 C3R20208HCLO 20.00 20.00 8.00 18P1717 17.00 17.00 C3RHCLOPK2 C3RHCLOMFK2 C3R24208HCLO 24.00 20.00 8.00 18P2117 21.00 17.00 C3RHCLOPK2 C3RHCLOMFK2 C3R24248HCLO 24.00 24.00 8.00 18P2121 21.00 21.00 C3RHCLOPK2 C3RHCLOMFK2 C3R30248HCLO 30.00 24.00 8.00 18P2721 27.00 21.00 C3RHCLOPK2 C3RHCLOMFK2 SKU: C3R30248HCLO -
Discontinued Products
(Discontinued) 94-169 CFM Filterfans PF GEN4 Series – (PF43000T12BK)
Features
- Maintains a UL Tested NEMA Type 12 seal against enclosure
- UL Recognized to UL 508A, category NITW2/8, UL File #E175229
- Patented “Click & Fit” design provides a hardware free installation!
- Plastic made from strong, heat resistant ABS-FR, UL 94 V0 fire approved material
- Fan Motor is CSA Approved
- Options: Black Grills
Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Part Number Light Gray RAL7035 Part Number Black RAL9011 Voltage Power Exhaust Filter Light Gray RAL7035 Exhaust Filter Black RAL9011 PF42500T12LG PF42500T12BK 115V 20W PFA40000LG PFA40000BK PF42500T12LG230 PF42500T12BK230 230V 18W PFA40000LG PFA40000BK PF42500T12LG24 PF42500T12BK24 24V 5W PFA40000LG PFA40000BK PF43000T12LG PF43000T12BK 115V 40W PFA40000LG PFA40000BK PF43000T12LG230 PF43000T12BK230 230V 39W PFA40000LG PFA40000BK PF43000T12LG24 PF43000T12BK24 24V 12W PFA40000LG PFA40000BK Airflow data PF 42500 PF 43000 PFA 40000 Filter material NEMA Type 12 Filtermat NEMA Type 12 Filtermat NEMA Type 12 Filtermat Unimpeded airflow 94 CFM 169 CFM – Capacity free-flow 53 W/K I88 W/K – Airflow in combination 67 CFM 142 CFM – (Filterfan + Exhaust Filter) (PF 42500 + PFA 40000) (PF 43000 + PFA 40000) – Capacity in combination 38 W/K 69 W/K – (Filterfan + Exhaust Filter) (PF 43000 + PFA 40000) (PF 43000 + PFA 40000) – Max. static pressure (Airflow = 0 m3/h) 49 Pa 112 Pa – Filtration efficiency 0.91 0.91 0.91 Filter material grade G 4 (DIN EN 779) G 4 (DIN EN 779) G 4 (DIN EN 779) Duty cycle 1 1 – Technical data PF 42500 PF 43000 PFA 40000 AC/DC AC/DC Outside dimensions in mm 252 x 252 x 97 252 x 252 x 113 252 x 252 x 38 (height x width x installation depth) Bearing type / Lagerart ball bearings – Fitting position / Einbaulage any, horizontal airflow preferred any Construction housing and guard of sprayed thermoplastic, self-extinguishing, UL 94 VO Weight 1.18 kg 1.67 kg 0.46 kg Safety protection in accordance with DIN 31 001 Color LG RAL 7035, Light Grey Color BK RAL9011 Black Connections / Anschlussart cage clamp cage clamp – Noise Level (EN ISO 3741) 43 dB (A) 46 dB (A) Supplementary data PF 42500 PF 43000 PFA 40000 Operating temperature – 15 °C (- 5 °F) to / bis + 55 °C (+ 131 °F) Storage temperature – 20 °C (- 4 °F) to / bis + 70 °C (+ 158 °F) Max. relative humidity 0.9 System of protection NEMA Type 12, IP 55 (EN 60 529), when installed as specified Basic Accessories parts kit filter mat, user manual radiant heater, fan heater, thermostat, hygrostat Approvals UL Recognized * Tolerance installation cutout 223 + 1/-0 thickness of material to 2 mm 224 + 1/-0 thickness of material > 2 mm < 3 mm SKU: PF43000T12BK -
Discontinued Products
(Discontinued) 94-169 CFM Filterfans PF GEN4 Series – (PF43000T12LG)
Features
- Maintains a UL Tested NEMA Type 12 seal against enclosure
- UL Recognized to UL 508A, category NITW2/8, UL File #E175229
- Patented “Click & Fit” design provides a hardware free installation!
- Plastic made from strong, heat resistant ABS-FR, UL 94 V0 fire approved material
- Fan Motor is CSA Approved
- Options: Black Grills
Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Part Number Light Gray RAL7035 Part Number Black RAL9011 Voltage Power Exhaust Filter Light Gray RAL7035 Exhaust Filter Black RAL9011 PF42500T12LG PF42500T12BK 115V 20W PFA40000LG PFA40000BK PF42500T12LG230 PF42500T12BK230 230V 18W PFA40000LG PFA40000BK PF42500T12LG24 PF42500T12BK24 24V 5W PFA40000LG PFA40000BK PF43000T12LG PF43000T12BK 115V 40W PFA40000LG PFA40000BK PF43000T12LG230 PF43000T12BK230 230V 39W PFA40000LG PFA40000BK PF43000T12LG24 PF43000T12BK24 24V 12W PFA40000LG PFA40000BK Airflow data PF 42500 PF 43000 PFA 40000 Filter material NEMA Type 12 Filtermat NEMA Type 12 Filtermat NEMA Type 12 Filtermat Unimpeded airflow 94 CFM 169 CFM – Capacity free-flow 53 W/K I88 W/K – Airflow in combination 67 CFM 142 CFM – (Filterfan + Exhaust Filter) (PF 42500 + PFA 40000) (PF 43000 + PFA 40000) – Capacity in combination 38 W/K 69 W/K – (Filterfan + Exhaust Filter) (PF 43000 + PFA 40000) (PF 43000 + PFA 40000) – Max. static pressure (Airflow = 0 m3/h) 49 Pa 112 Pa – Filtration efficiency 0.91 0.91 0.91 Filter material grade G 4 (DIN EN 779) G 4 (DIN EN 779) G 4 (DIN EN 779) Duty cycle 1 1 – Technical data PF 42500 PF 43000 PFA 40000 AC/DC AC/DC Outside dimensions in mm 252 x 252 x 97 252 x 252 x 113 252 x 252 x 38 (height x width x installation depth) Bearing type / Lagerart ball bearings – Fitting position / Einbaulage any, horizontal airflow preferred any Construction housing and guard of sprayed thermoplastic, self-extinguishing, UL 94 VO Weight 1.18 kg 1.67 kg 0.46 kg Safety protection in accordance with DIN 31 001 Color LG RAL 7035, Light Grey Color BK RAL9011 Black Connections / Anschlussart cage clamp cage clamp – Noise Level (EN ISO 3741) 43 dB (A) 46 dB (A) Supplementary data PF 42500 PF 43000 PFA 40000 Operating temperature – 15 °C (- 5 °F) to / bis + 55 °C (+ 131 °F) Storage temperature – 20 °C (- 4 °F) to / bis + 70 °C (+ 158 °F) Max. relative humidity 0.9 System of protection NEMA Type 12, IP 55 (EN 60 529), when installed as specified Basic Accessories parts kit filter mat, user manual radiant heater, fan heater, thermostat, hygrostat Approvals UL Recognized * Tolerance installation cutout 223 + 1/-0 thickness of material to 2 mm 224 + 1/-0 thickness of material > 2 mm < 3 mm SKU: PF43000T12LG -
Discontinued Products
Type 4X Polyester Junction Box w/ Window PJ Series – (PJ16148HW) (DISCONTINUED)
Discontinued ProductsType 4X Polyester Junction Box w/ Window PJ Series – (PJ16148HW) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
- Ideal in applications with high temperatures or highly corrosive environments.
Standards
- UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
- CSA Type 1, 2, 3, 4, 4X, 12 and 13
- Complies with
- NEMA Type 1, 2, 3, 4, 4X, 12, & 13
- IEC 60529, IP66
Construction
- Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
- Enhanced UV inhibitors protect against outdoor weathering.
- Standard JIC sizes under 18″x16″.
- Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
- Stainless steel draw type “snap latch” door fasteners.
- Door fasteners include a provision for padlocking.
- Enclosures are available with bonded polycarbonate viewing windows.
- Door is supported with a continuous stainless steel hinge.
- Captive oil resistant gasket provides a positive seal.
- Threaded brass inserts are provided for mounting feet to the rear of the enclosure.
- Stainless steel mounting brackets and hardware are provided for mounting to the rear of the enclosure.
- Operating temperatures between 130°C and -40°C (266°F to -40°F).
- Impact index of 6.78J (5 ft/lb).
- For corrosion resistance information, please refer to table in the Technical Information section.
Finish
- Fiberglass polyester material has a gray finish.
- Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.
Accessories
- Additional Inner Panels
- Terminal Kit Assemblies
- Pole Mounting Kit
- PJ/PJU/PCJ Replacement Hardware Kits
- PJ Stainless Replacement Mounting Feet
- Climate Control
- General Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Lift-Off Hinged Snap Latch Twist Latch Enclosure Optional Inner Panel Part No. Part No. Part No. Part No. H W D H W Part No. PJ664W PJ664HW PJ664LW PJ664TW 6.10 6.10 4.18 4.88 4.88 14R0505 PJ864W PJ864HW PJ864LW PJ864TW 8.00 6.12 4.13 6.75 4.88 14R0705 PJ1084W PJ1084HW PJ1084LW PJ1084TW 10.13 8.26 4.13 8.75 6.88 14R0907 PJ1086W PJ1086HW PJ1086LW PJ1086TW 10.13 8.26 6.13 8.75 6.88 14R0907 PJ12106W PJ12106HW PJ12106LW PJ12106TW 12.13 10.26 6.13 10.75 8.88 14R1109 PJ12124W PJ12124HW PJ12124LW PJ12124TW 12.13 12.13 4.13 10.75 10.88 14R1111 PJ12126W PJ12126HW PJ12126LW PJ12126TW 12.13 12.13 6.13 10.75 10.88 14R1111 PJ14126W PJ14126HW PJ14126LW PJ14126TW 14.13 12.26 6.13 12.75 10.88 14R1311 PJ16148W PJ16148HW PJ16148LW PJ16148TW 16.27 14.40 8.13 14.75 12.88 14R1513 PJ18168W PJ18168HW PJ18168LW PJ18168TW 18.40 16.40 8.13 16.88 14.88 P1868 PJ20168W PJ20168HW PJ20168LW PJ20168TW 20.00 16.00 8.13 18.44 14.44 P2068 SKU: PJ16148HW -
Discontinued Products
(Discontinued) Compact LED Light Kit LEDLK Series – (LEDDCMSSCR)
Our compact LED light kit provides efficient lighting solution for most enclosure applications without taking up valuable interior space. Available in magnet or screw mounting and AC or DC power options.
Features
- Housing constructed in transparent plastic.
- Screw or magnet mounting.
- Available with rocker switch or motion sensor.
- Easily connect up to ten (10) light kits together in a daisy chain using LEDXXCORDCON cords.
- Connection: 2-pole plug with snap lock; AC: max. 2.5 A / AC 240 V, white connector; DC: max. 2.5 A / DC 60 V, blue connector.
- Requires hard-wired connection using LEDXXCORDPOWR power cord with leads and plug or power brick (not included).
Specifications
- LED provide 400 Lm at 120° (1,200 Lm at 360° or equivalent 95W light bulb).
- LED temperature 6,000 to 7,000 K.
- Operating / Storage temperature: -22 to +140 °F (-30 to +60 °C) / -40 to +185 °F (-40 to +85 °C).
- Operating / Storage humidity: max. 90 %RH (non-condensing).
- Service life: 60,000 hrs. at 68 °F (20 °C).
- Max. 5 W power consumption (~ 75 W incandescent bulb)
- Protection class / Protection type: II (double insulated) / IP20
Note that the cord on this product is intended to be hard-wired. There are currently no standard plug types for this product.
Gallery
Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
LED Light Kits
Part No. Voltage On/Off Mount LEDACSWMAG 90-260V AC Switch Magnet LEDACMSMAG 90-260V AC Sensor Magnet LEDACSWSCR 90-260V AC Switch Screw LEDACMSSCR 90-260V AC Sensor Screw LEDDCSWMAG 20-60V DC Switch Magnet LEDDCMSMAG 20-60V DC Sensor Magnet LEDDCSWSCR 20-60V DC Switch Screw LEDDCMSSCR 20-60V DC Sensor Screw LED Light Kit Cords
Units shown: inch. Switch units to: mm
Part No. Type Source Length LEDACCORDPOW Power Cord w/leads AC 78.75 LEDDCCORDPOW Power Cord w/leads DC 78.75 LEDACCORDCON Connector/Daisy Chain Cord AC 39.38 LEDDCCORDCON Connector/Daisy Chain Cord DC 39.38 Light Channel Hardware
Part No. Description LCMTG1032 Light channel mounting hardware – 4 x spring nuts/10-32 screws SKU: LEDDCMSSCR -
Discontinued Products
(Discontinued) Compact LED Light Kit LEDLK Series – (LEDDCMSMAG)
Our compact LED light kit provides efficient lighting solution for most enclosure applications without taking up valuable interior space. Available in magnet or screw mounting and AC or DC power options.
Features
- Housing constructed in transparent plastic.
- Screw or magnet mounting.
- Available with rocker switch or motion sensor.
- Easily connect up to ten (10) light kits together in a daisy chain using LEDXXCORDCON cords.
- Connection: 2-pole plug with snap lock; AC: max. 2.5 A / AC 240 V, white connector; DC: max. 2.5 A / DC 60 V, blue connector.
- Requires hard-wired connection using LEDXXCORDPOWR power cord with leads and plug or power brick (not included).
Specifications
- LED provide 400 Lm at 120° (1,200 Lm at 360° or equivalent 95W light bulb).
- LED temperature 6,000 to 7,000 K.
- Operating / Storage temperature: -22 to +140 °F (-30 to +60 °C) / -40 to +185 °F (-40 to +85 °C).
- Operating / Storage humidity: max. 90 %RH (non-condensing).
- Service life: 60,000 hrs. at 68 °F (20 °C).
- Max. 5 W power consumption (~ 75 W incandescent bulb)
- Protection class / Protection type: II (double insulated) / IP20
Note that the cord on this product is intended to be hard-wired. There are currently no standard plug types for this product.
Gallery
Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
LED Light Kits
Part No. Voltage On/Off Mount LEDACSWMAG 90-260V AC Switch Magnet LEDACMSMAG 90-260V AC Sensor Magnet LEDACSWSCR 90-260V AC Switch Screw LEDACMSSCR 90-260V AC Sensor Screw LEDDCSWMAG 20-60V DC Switch Magnet LEDDCMSMAG 20-60V DC Sensor Magnet LEDDCSWSCR 20-60V DC Switch Screw LEDDCMSSCR 20-60V DC Sensor Screw LED Light Kit Cords
Units shown: inch. Switch units to: mm
Part No. Type Source Length LEDACCORDPOW Power Cord w/leads AC 78.75 LEDDCCORDPOW Power Cord w/leads DC 78.75 LEDACCORDCON Connector/Daisy Chain Cord AC 39.38 LEDDCCORDCON Connector/Daisy Chain Cord DC 39.38 Light Channel Hardware
Part No. Description LCMTG1032 Light channel mounting hardware – 4 x spring nuts/10-32 screws SKU: LEDDCMSMAG -
Discontinued Products
Mounting Rack Rail Swing Frame S2CSWF Series – (2CSFT19) (DISCONTINUED)
- Available in 19″ and 24″ widths.
- Variable depth feature allows front to rear adjustment.
- Installs with either left or right hinging.
- Mounts onto Rail Support Kits (not included).
- Clip nuts required for mounting to punched rails.
- Finished in textured black.
- TAA compliant for GSA Schedule purchases.
- RoHS Compliant.
- Manufactured in North America.
Gallery
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Panel Part No. Fits Console Unit Fits Console Size Width Height A B 2CSFT19 Turrets/Terminal 24,36,48,60 19″ 8U 15.75 19.28 2CSFT24 Turrets/Terminal 36,48,60 24″ 8U 15.75 24.28 2CSFB19 Bases 24,36,48,60 19″ 12U 22.09 19.28 2CSFB24 Bases 36,48,60 24″ 12U 22.09 24.28 SKU: 2CSFT19 -
Discontinued Products
Type 4 Mild Steel Junction Box 1414 N4 Series – (1414N4O10) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides protection where equipment may be hosed down or otherwise be very wet, or in outdoor applications for full weather protection.
Standards
- UL 508A Type 3R, 4, 12 and 13
- CSA Type 3R, 4, 12 and 13
- Complies with
- NEMA Type 3R, 4, and 12
- IEC 60529, IP66
Construction
- Body formed from 16 or 14 gauge steel. Covers are formed from 14 gauge steel.
- Smooth, continuously welded seams without knockouts, cutouts or holes.
- Welded brackets provide for enclosure mounting.
- Lift off cover is secured with stainless steel clamps and screws.
- Seamless poured-in place gasket.
- All models larger than 4″ x 4″ include a removable 14 gauge inner panel.
- Internal threaded weld studs are provided for mounting inner panels.
- A bonding stud is provided on the door and a grounding stud is provided on the enclosure.
Finish
- Cover and enclosure are phosphatized, finished in recoatable smooth ANSI 61 gray powder coating.
- Removable inner panel is finished in white powder coating.
Accessories
- Additional Inner Panels
- Terminal Kit Assemblies
- Swing Panel Kit
- Door Clamping Hardware
- Climate Control
- General Accessories
Part Details
Click Part No, below, for details (e.g., Product drawings, assembly instructions, ship weight)
Units shown: inch. Switch units to: mm
Enclosure Panel Part No. H W D H W 1414N4A¹ 4.00 4.00 3.00 – – 1414N4C 6.00 4.00 3.00 4.88 2.88 1414N4G 8.00 6.00 3.50 6.75 4.88 1414N4E 6.00 6.00 4.00 4.88 4.88 1414N4I 10.00 8.00 4.00 8.75 6.88 1414N4K 12.00 10.00 5.00 10.75 8.88 1414N4M6 14.00 12.00 6.00 12.75 10.88 1414N4O6 16.00 14.00 6.00 14.75 12.88 1414N4M8 14.00 12.00 8.00 12.75 10.88 1414N4O10 16.00 14.00 10.00 14.75 12.88 SKU: 1414N4O10 -
Discontinued Products
Type 4X Polyester Junction Box w/ Window PJU Series – (PJU14126HW) (DISCONTINUED)
Discontinued ProductsType 4X Polyester Junction Box w/ Window PJU Series – (PJU14126HW) (DISCONTINUED)
Application
- Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
- Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
- Ideal in applications with high temperatures or highly corrosive environments.
Standards
- UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
- CSA Type 1, 2, 3, 4, 4X, 12 and 13
- Complies with
- NEMA Type 1, 2, 3, 4, 4X, 12 and 13
- IEC 60529, IP66
Construction
- Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
- Enhanced UV inhibitors protect against outdoor weathering.
- Standard JIC sizes under 18″x16″.
- Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
- Various latching options.
- Enclosures are available with bonded polycarbonate viewing windows.
- Door is supported with a continuous stainless steel hinge pin.
- Captive oil resistant gasket provides a positive seal.
- Threaded brass inserts are provided for mounting feet to the rear of the enclosure.
- Operating temperatures between 130°C and -40°C (266°F to -40°F).
- Impact index of 6.78J (5 ft/lb).
- For corrosion resistance information, please refer to table in the Technical Information section.
Finish
- Fiberglass polyester material has a light gray finish.
- Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.
Accessories
SKU: PJU14126HW -
Discontinued Products
Type 12 Pull Through Wireway 1487 Series – (1487E24) (DISCONTINUED)
Application
- Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
- Ideal for connecting machines to control panels or power sources.
Standards
- UL 870 Type 1 (unless marked¹)
- CSA Type 1 (unless marked¹)
- Complies with
- NEMA Type 12
- IEC 60529, IP54
Construction
- Bodies and covers are formed from 14 gauge steel with 10 gauge steel flanges.
- Continuous flange around wireway ends, requires cables to be pulled through. (For lay-in style, see 1485 Series.)
- Smooth continuously welded seams.
- Interior surfaces are smooth to prevent wire damage during installation.
- Butt hinged covers are secured with easily operated screw clamps.
- Oil resistant gaskets are permanently secured.
- Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
- One gasket kit, complete with hardware is provided with each straight section or fitting.
Finish
- Sections and fittings are finished in ANSI 61 gray.
Accessories
SKU: 1487E24
