American Tech Supply Full Catalog

Application

• Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
• Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
• Ideal in applications with high temperatures or highly corrosive environments.

Standards

• UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
• CSA Type 1, 2, 3, 4, 4X, 12 and 13
• Complies with
  • NEMA Type 1, 2, 3, 4, 4X, 12 and 13
  • IEC 60529, IP66

Construction

• Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
• Enhanced UV inhibitors protect against outdoor weathering.
• Standard JIC sizes under 18″ x 16″.
• Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
• Stainless steel draw type “snap latch” door fasteners.
• Door fasteners include a provision for padlocking.
• Enclosure available with clear Polycarbonate cover to 16″ x 14″.
• Molded hinge with stainless steel pin.
• Captive oil resistant gasket provides a positive seal.
• Available with Polycarbonate flange or foot mount brackets for multi-directional mounting.
• Operating temperatures between 130°C and -40°C (266°F to -40°F).
• Impact index of 6.78J (5 ft/lb).
• For corrosion resistance information, please refer to table in the Technical Information section.

Finish

• Fiberglass polyester material has a gray finish.
• Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.

Accessories

Application  

• Designed to enclose and protect electrical wiring from dirt, dust, oil and water.
• All sections and fittings are completely open on each side to allow wires and cables to be placed into the wireway without “pulling through”.

Standards

• UL 870 Type 1 (unless marked¹)
• CSA Type 1 (unless marked¹)
• Complies with
  • NEMA Type 12
  • IEC 60529, IP54

Construction

• Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.
• Flanges are open at the top to allow cables to lay in when doors open.
• 12” x 6” size has a 12 gauge steel body with a 14-gauge cover.
• Smooth continuously welded seams.
• Interior surfaces are smooth to prevent wire damage during 
  installation.
• Butt hinged cover is secured with easily operated quick release clamps.
• Oil resistant gaskets are permanently secured.
• Solid oil resistant gaskets are used between flanges when sections and fittings are bolted together.
• One gasket kit, complete with hardware is provided with each straight section or fitting.
• Sealing plate is supplied.
• Flange junctions are sealed with gasket sealing plates, which are put in place after wiring is completed. One is supplied with all straight sections and most fittings; see table for exact number.

Finish

• Sections and components are finished in ANSI 61 gray powder coating.

Notes

• When joining a wireway section or fitting to an enclosure be sure to order a box connector.
• When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing plate is required at each junction; necessary kits are supplied with each section and fitting. See table, extra kits may be ordered if necessary.
• When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-off fitting, an angle sealing plate is required at each junction.
• Necessary kits are supplied with each section and fitting – see table. Extra kits, although not normally required, are necessary when joining lay-in wireway to a non-lay-in section or fitting section.

Accessories

Application

• Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures.
• Provides outstanding insulation and protection where equipment may be hosed down or be very wet.
• Ideal in applications with high temperatures or highly corrosive environments.

Standards

• UL 508A Type 1, 2, 3, 4, 4X, 12 and 13
• CSA Type 1, 2, 3, 4, 4X, 12 and 13
• Complies with
  • NEMA Type 1, 2, 3, 4, 4X, 12 and 13
  • IEC 60529, IP66

Construction

• Molded fiberglass polyester enclosure with matching cover is easily punched, cut, or drilled.
• Enhanced UV inhibitors protect against outdoor weathering.
• Standard JIC sizes under 18″ x 16″.
• Threaded brass inserts are provided for optional inner panel or terminal kit mounting. Mounting hardware is included.
• Stainless steel draw type “snap latch” door fasteners.
• Door fasteners include a provision for padlocking.
• Enclosure available with clear Polycarbonate cover to 16″ x 14″.
• Molded hinge with stainless steel pin.
• Captive oil resistant gasket provides a positive seal.
• Available with Polycarbonate flange or foot mount brackets for multi-directional mounting.
• Operating temperatures between 130°C and -40°C (266°F to -40°F).
• Impact index of 6.78J (5 ft/lb).
• For corrosion resistance information, please refer to table in the Technical Information section.

Finish

• Fiberglass polyester material has a gray finish.
• Optional inner panels are available in white powder coated finished steel or unfinished aluminum, or Fiberglass.

Accessories

Application

• Designed to insulate and protect controls and components in both indoor and outdoor conditions
• Ideal for industrial pump controls, waste water, irrigation control along with solar/wind and chemical plants

Standards

• UL 508A Type 1, 2, 3, 3R, 4, 4X, 12 and 13
• CSA Type 1, 2, 3, 3R, 4, 4X, 12 and 13
• Complies with
  • NEMA Type 1, 2, 3, 3R, 4, 4X, 12 and 13
  • IEC 60529, IP66 
  • Flammability V-O per UL 94
  • UV rating (f1) per UL746C – UV stabilized for outdoor use
  • Compliant with RoHS directive